View DS96-L147-203_1328191.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

cx81801-7x/8x smartv.xx modem data sheet 102199b conexant iii contents 1. introduction................................................................................................................... .......................1-1 1.1 overview ....................................................................................................................... .................................................. 1-1 1.2 applicat ions ................................................................................................................... ................................................. 1-2 1.3 features ....................................................................................................................... ................................................... 1-4 1.3.1 general mode m features......................................................................................................... ....................... 1-4 1.3.2 smartdaa featur es .............................................................................................................. .......................... 1-5 1.3.3 applicat ions................................................................................................................... ................................. 1-5 1.4 technical overview ............................................................................................................. ............................................ 1-6 1.4.1 general d escripti on ............................................................................................................ ............................ 1-6 1.4.2 mcu firm ware................................................................................................................... ............................. 1-6 1.4.3 operating modes ................................................................................................................ ............................ 1-6 1.4.3.1 data/fax modes................................................................................................................. ......... 1-6 1.4.3.2 v.44 data co mpressi on.......................................................................................................... .... 1-7 1.4.3.3 worldwide op eration............................................................................................................ ...... 1-7 1.4.3.4 tam mode....................................................................................................................... ........... 1-8 1.4.3.5 speakerphone mode (s models )................................................................................................ 1-9 1.4.4 reference designs.............................................................................................................. ............................ 1-9 1.5 hardware de scription ........................................................................................................... .......................................... 1-9 1.5.1 cx81801 modem devi ce ........................................................................................................... ..................... 1-9 1.5.2 digital isolat ion ba rrier...................................................................................................... ........................... 1-10 1.5.3 cx20493 smartdaa line side devi ce.............................................................................................. ............ 1-10 1.5.4 cx20442 voice codec ............................................................................................................ ...................... 1-10 1.6 at commands .................................................................................................................... .......................................... 1-10 2. technical specifications ....................................................................................................... ................2-1 2.1 serial dte inte rface oper ation................................................................................................. ....................................... 2-1 2.1.1 automatic speed/format sensing ................................................................................................. ................. 2-1 2.2 parallel host bus interface operation.......................................................................................... ................................... 2-2 2.3 establishing data modem conn ections ............................................................................................ .............................. 2-2 2.3.1 dialing ........................................................................................................................ .................................... 2-2 2.3.2 telephone number direct ory..................................................................................................... ..................... 2-2 2.3.3 modem handshak ing prot ocol ..................................................................................................... .................. 2-2 2.3.4 call progress tone detect ion ................................................................................................... ...................... 2-2 2.3.5 answer tone detect ion.......................................................................................................... ......................... 2-2 2.3.6 ring detection................................................................................................................. ............................... 2-2 2.3.7 billing pr otection ............................................................................................................. ............................... 2-3 2.3.8 connection speeds.............................................................................................................. ........................... 2-3 2.3.9 automode ....................................................................................................................... ................................ 2-3 2.4 data mode ...................................................................................................................... ................................................ 2-4
cx81801-7x/8x smartv.xx modem data sheet iv conexant 102199b 2.4.1 speed buffering (n ormal mode) .................................................................................................. .................. 2-4 2.4.2 flow c ontrol ................................................................................................................... ................................ 2-4 2.4.3 escape sequence detect ion...................................................................................................... ...................... 2-4 2.4.4 break detection ................................................................................................................ ............................ 2-4 2.4.5 telephone line monito ring...................................................................................................... ....................... 2-4 2.4.6 fall forward/fallback (v.92/ v.90/v.34/v.32 bis/ v.32) ........................................................................... ........ 2-4 2.4.7 retrain ........................................................................................................................ .................................... 2-5 2.4.8 programmable inactivity timer .................................................................................................. .................... 2-5 2.4.9 dte signal monitoring (seria l dte interface only) .............................................................................. .......... 2-5 2.5 v.92 feat ures .................................................................................................................. ................................................ 2-5 2.5.1 modem-on- hold .................................................................................................................. ........................... 2-5 2.5.2 quick connect .................................................................................................................. .............................. 2-6 2.5.3 pcm upstream ................................................................................................................... ............................ 2-6 2.6 error correction and data comp ressi on.......................................................................................... ............................... 2-6 2.6.1 v.42 error co rrection .......................................................................................................... ........................... 2-6 2.6.2 mnp 2-4 error correction ....................................................................................................... ....................... 2-6 2.6.3 v.44 data co mpressi on.......................................................................................................... ........................ 2-6 2.6.4 v.42 bis data compression ...................................................................................................... ...................... 2-6 2.6.5 mnp 5 data compr ession ......................................................................................................... ..................... 2-7 2.7 telephony ex tensions........................................................................................................... .......................................... 2-7 2.7.1 line in use detection .......................................................................................................... ........................... 2-7 2.7.2 extension pick up detection ..................................................................................................... ....................... 2-7 2.7.3 remote hangup detect ion........................................................................................................ ...................... 2-8 2.8 fax class 1 and fax class 1.0 oper ation ........................................................................................ ................................ 2-8 2.9 point-of-sal es suppor t ......................................................................................................... .......................................... 2-8 2.10 voice/audi o mode ............................................................................................................... ........................................... 2-8 2.10.1 online voice command mode ...................................................................................................... .................. 2-8 2.10.2 voice recei ve mode ............................................................................................................. .......................... 2-8 2.10.3 voice transm it mode ............................................................................................................ ......................... 2-9 2.10.4 full-duplex receive a nd transmit mode .......................................................................................... .............. 2-9 2.10.5 audio mode ..................................................................................................................... ............................... 2-9 2.10.6 tone dete ctors ................................................................................................................. .............................. 2-9 2.10.7 speakerphone mode.............................................................................................................. ......................... 2-9 2.11 v.80 synchronous access mode ( sam) - video c onferen cing ........................................................................ .............. 2-9 2.12 full-duplex speakerphone (fd sp) mode (s mode ls)................................................................................ ................... 2-10 2.13 caller id ...................................................................................................................... .................................................. 2-10 2.14 worldwide count ry s upport ...................................................................................................... ................................... 2-10 2.15 diagnos tics .................................................................................................................... ............................................... 2-11 2.15.1 commanded tests................................................................................................................ ........................ 2-11 2.15.2 power on r eset t ests ........................................................................................................... ....................... 2-11 2.16 low power sl eep mode ........................................................................................................... ..................................... 2-12 3. hardware interface ............................................................................................................. ..................3-1 3.1 cx81801 modem hardware pins and signals ........................................................................................ ........................ 3-1 3.1.1 common to parallel and serial interface c onfigurat ions......................................................................... ....... 3-1 3.1.1.1 lsd interface (through dib).................................................................................................... .. 3-1 3.1.1.2 call progress speaker interface ................................................................................................ .3-1 3.1.1.3 voice relay interface (s models) ............................................................................................... 3-1 3.1.1.4 serial eeprom interface........................................................................................................ .... 3-1 3.1.1.5 external bus interface ......................................................................................................... ....... 3-2
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant v 3.1.2 serial interface c onfigurati on only............................................................................................ ..................... 3-2 3.1.2.1 serial dte interface and indicato r outputs (parif = low) ........................................................ 3-2 3.1.3 parallel interface configurat ion only (par if = high)........................................................................... .......... 3-3 3.1.3.1 parallel host bus interface .................................................................................................... ..... 3-3 3.1.4 cx81801 modem inte rface si gnals................................................................................................ ................ 3-3 3.2 cx20493 lsd hardware pins and signals .......................................................................................... ......................... 3-22 3.2.1 cx20493 lsd signa l summa ry..................................................................................................... ............... 3-22 3.2.1.1 smart modem interfa ce (through dib) ................................................................................... 3-22 3.2.1.2 telephone line interf ace ....................................................................................................... ... 3-22 3.2.1.3 voltage references............................................................................................................. ...... 3-22 3.2.1.4 general purpose input/output.................................................................................................. 3 -23 3.2.1.5 no connects .................................................................................................................... ......... 3-23 3.2.2 cx20493 lsd pin assignments and signal de finiti ons ............................................................................. .. 3-23 3.3 cx20442 vc hardware pins a nd signals (s mode ls)................................................................................ ................... 3-28 3.3.1 cx20442 vc sign al su mmary ...................................................................................................... ................ 3-28 3.3.1.1 speakerphone in terfac e......................................................................................................... ... 3-28 3.3.1.2 telephone handset/head set interf ace...................................................................................... 3-28 3.3.1.3 cx81801 modem in terface ....................................................................................................... 3 -28 3.3.1.4 host interface................................................................................................................. .......... 3-28 3.3.2 cx20442 vc pin assignments and signal de finiti ons .............................................................................. ... 3-29 3.4 electrical and environm ental specifications .................................................................................... ............................. 3-35 3.4.1 operating conditions, absolute maximum ratings, and power requirement s ........................................... 3-35 3.4.2 interface and ti ming wavef orms ................................................................................................. ................ 3-37 3.4.2.1 external memory bus timing ................................................................................................... 3- 37 3.4.2.2 parallel host bus timing ....................................................................................................... ... 3-39 3.4.2.3 serial dte interface........................................................................................................... ....... 3-41 3.5 crystal speci fications ......................................................................................................... .......................................... 3-42 4. package dimensions ............................................................................................................. ...............4-1 5. parallel host interface ........................................................................................................ ..................5-1 5.1 overview ....................................................................................................................... .................................................. 5-1 5.2 register signa l definitions .................................................................................................... ......................................... 5-3 5.2.1 ier - interrupt enable regist er (addr = 1, dlab = 0) ........................................................................... ......... 5-3 5.2.2 fcr - fifo control register (addr = 2, write only) ............................................................................. .......... 5-4 5.2.3 iir - interrupt identifier register (addr = 2) ................................................................................. ................. 5-5 5.2.4 lcr - line control re gister (a ddr = 3) ......................................................................................... ................. 5-6 5.2.5 mcr - modem control re gister (a ddr = 4)........................................................................................ ............ 5-7 5.2.6 lsr - line status re gister (a ddr = 5).......................................................................................... .................. 5-7 5.2.7 msr - modem status re gister (a ddr = 6) ......................................................................................... ............ 5-9 5.2.8 rbr - rx buffer (receiver buffer register) (addr = 0, dlab = 0) ................................................................ 5-9 5.2.9 thr - tx buffer (transmitter holding register) (addr = 0, dlab = 0).......................................................... 5- 9 5.2.10 divisor registers (addr = 0 and 1, dlab = 1)................................................................................... ........... 5-10 5.3 receiver fifo interrupt operation .............................................................................................. .................................. 5-10 5.3.1 receiver data available interrupt .............................................................................................. ................... 5-10 5.3.2 receiver character timeout interrupts.......................................................................................... ............... 5-11 5.4 transmitter fifo in terrupt operation ........................................................................................... ................................ 5-11 5.4.1 transmitter empty interrupt.................................................................................................... ..................... 5-11
cx81801-7x/8x smartv.xx modem data sheet vi conexant 102199b figures figure 1-1. smartv.xx modem si mplified interf ace diagram ....................................................................... ..................... 1-3 figure 1-2. smartv.xx m odem major in terfaces................................................................................... ............................. 1-3 figure 2-1. tmind# test results pulse cycles ................................................................................... ............................. 2-12 figure 3-1. cx81801 modem hardware signals for parallel interf ace (parif = high) ............................................... ....... 3-4 figure 3-2. cx81801 modem 128-pin tqfp pin signa ls for parallel interf ace (parif = high) ....................................... .. 3-5 figure 3-3. cx81801 modem hardware signals for serial interf ace (parif = low).................................................. ...... 3-12 figure 3-4. cx81801 modem 128-pin tqfp pin signa ls for serial interf ace (parif = low).......................................... .3-13 figure 3-5. cx20493 lsd hard ware interfac e sign als ............................................................................. ........................ 3-23 figure 3-6. cx20493 lsd 28-pin qfn pi n signa ls................................................................................. .......................... 3-24 figure 3-7. cx20442 vc ha rdware inte rface si gnals .............................................................................. ......................... 3-30 figure 3-8. cx20442 vc 32- pin tqfp pi n signa ls ................................................................................. .......................... 3-30 figure 3-9. waveforms - external me mory bus.................................................................................... ............................ 3-38 figure 3-10. waveforms - parallel ho st bus..................................................................................... ................................ 3-40 figure 3-11. waveforms - serial dte interf ace .................................................................................. .............................. 3-41 figure 4-1. package dime nsions - 128- pin tq fp.................................................................................. ............................. 4-2 figure 4-2. package dime nsions - 32- pin tq fp ................................................................................... .............................. 4-3 figure 4-3. package dime nsions - 28- pin qfn.................................................................................... ............................... 4-4
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant vii tables table 1-1. smartv.xx mode m models and functions ................................................................................ ........................ 1-2 table 1-2. default countries s upporte d......................................................................................... ..................................... 1-8 table 2-1. +ms command au tomode connectivity ................................................................................... ......................... 2-3 table 3-1. cx81801 modem 128-pin tqfp pin sign als for parallel interf ace (parif = high)........................................ ... 3-6 table 3-2. cx81801 modem pin signal definiti ons for parallel interf ace (parif = high) .......................................... ....... 3-8 table 3-3. cx81801 modem 128-pin tqfp pin sign als for serial interf ace (parif = low) ........................................... .3-14 table 3-4. cx81801 modem pin signal definiti ons for serial interf ace (parif = low)............................................. ...... 3-16 table 3-5. cx81801 modem i/o type de finitions .................................................................................. .......................... 3-21 table 3-6. cx81801 modem dc electrical char acteristics ......................................................................... ...................... 3-21 table 3-7. cx20493 lsd 28-pin qfn pi n signals .................................................................................. .......................... 3-24 table 3-8. cx20493 lsd hard ware signal de finitions ............................................................................. ........................ 3-25 table 3-9. cx20493 lsd gpio dc electrical characteristics ...................................................................... ..................... 3-27 table 3-10. cx20493 avdd dc el ectrical charac terist ics......................................................................... ........................ 3-27 table 3-11. cx20442 vc 32- pin tqfp pi n signa ls................................................................................. .......................... 3-31 table 3-12. cx20442 vc pi n signal de finiti ons .................................................................................. ............................. 3-32 table 3-13. cx20442 vc dc electrical char acteris tics........................................................................... .......................... 3-33 table 3-14. cx20442 vc analog electrical ch aracteris tics....................................................................... ........................ 3-34 table 3-15. oper ating c onditi ons ............................................................................................... ...................................... 3-35 table 3-16. cx81801 abso lute maximu m rati ngs ................................................................................... ........................ 3-35 table 3-17. cx20493 abso lute maximu m rati ngs ................................................................................... ........................ 3-35 table 3-18. cx20442 abso lute maximu m rati ngs ................................................................................... ........................ 3-36 table 3-19. current a nd power requi rements..................................................................................... ............................. 3-36 table 3-20. timing - ex ternal memory bus ....................................................................................... ............................... 3-37 table 3-21. timing - parallel host bus ......................................................................................... .................................... 3-39 table 3-22. crystal specifications............................................................................................. ........................................ 3-42 table 5-1. parallel interface registers ........................................................................................ ........................................ 5-2 table 5-2. interrupt s ources and rese t cont rol ................................................................................. ................................ 5-5 table 5-3. progra mmable baud rates ............................................................................................. ................................. 5-10

cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 1-1 1. introduction 1.1 overview the conexant ? smartv.xx modem is a full-featur ed, worldwide, controller-based modem that integrates modem controller (mcu), modem data pump (mdp), 256 kb rom, 32 kb ram, and smartdaa system side device (ssd) functions onto a single die. the modem operates by executing firmware from internal rom and ram. optional customized firmware is supported with optional external flash rom memory. additionally, added/modified country profiles are supported by internal sram patch (maximum of one profile) or serial eepro m. downloadable ar chitecture supports downloading of customized mcu firmware from the host/dte to the smartv.xx modem. the smartv.xx modem device set consists of a cx81801 modem device in a 128-pin tqfp and a cx20493 smartdaa line side device (lsd) in a 28-pin qfn. conexant?s smartdaa ? technology eliminates the need fo r a costly analog transformer, relays and opto-isolations typically used in discrete daa (data access arrangement) implementations. the smartdaa architecture also simplifies product implementation by eliminating the need for country-specific board configurations enabling worldwide homologation of a single modem board design and a single bill of materials (bom). low profile, small tqfp and qfn packages with reduced voltage operation and low power consumption makes this device set an ideal solution for embedded and palmtop application using parallel host or serial dte interface. the smartv.xx modem supports data rates up to v.92, data compression, error correction, fax rates up to 14.4 kbps and speakerphone mode. in v.92 and v.90 (v.92 models ) data modes, the modem can receive data at speeds up to 56 kbps. in v.34 data mode (v.92 and v.34 models), the modem can receive data at speeds up to 33.6 kbps. in v.32 bis data m ode, the modem can receive data at speeds up to 14.4 kbps. data compress (v.44/v.42bis/mnp5) and error correction (v.42/mnp 2-4) modes are supported to maximize data throughput and da ta transfer integrity. non-error-correction mode is also supported. fax group 3 send and receive rates are suppor ted up to 14.4 kbps with t.30 protocol. the smartv.xx modem operates with pstn telephone lines worldwide. s models, using the optional cx20442 voice codec (vc) in a 32-pin tqfp, support position independent, full-duplex speakerphon e (fdsp) operation using microphone and speaker, as well as other voice/tam applications using handset or headset. table 1-1 lists the available models. a simp lified device interface drawing is shown in figure 1-1. a functional interface drawin g showing optional memory is shown in figure 1-2.
cx81801-7x/8x smartv.xx modem data sheet 1-2 conexant 102199b 1.2 applications ? set top boxes ? gaming devices ? point of sale terminals ? remote monitoring and data collections systems ? handheld computers ? other embedded systems table 1-1. smartv.xx modem models and functions model/order/part numbers supported functions marketing name device set order no. modem device [128-pin tqfp] part no. line side device (lsd) [28-pin qfn] part no. voice codec (vc) [32-pin tqfp] part no. v.90 data, qc, moh v.34 data v.32 bis data, v.44 data compression, v.17 fax, tam, worldwide voice/ fdsp smartv.92 ds56-l147-203 cx81801-74 cx20493-21 ? y y y ? smartv.92/s ds56-l147-204 cx81801-74 cx20493-21 cx20442-11 y y y y smartv.92/lf ds56-l147-206 cx81801-84 cx20493-31 ? y y y ? smartv.34 ds28-l147-203 cx81801-72 cx20493-21 ? ? y y ? smartv.34/s ds28-l147-204 cx81801-72 cx20493-21 cx20442-11 ? y y y smartv.34/lf ds28-l147-206 cx81801-82 cx20493-31 ? ? y y ? smartv.32bis DS96-L147-203 cx81801-73 cx20493-21 ? ? ? y ? smartv.32bis/s ds96-l147-204 cx81801-73 cx20493-21 cx20442-11 ? ? y y smartv.32bis/lf ds96-l147-206 cx81801-83 cx20493-31 ? ? ? y ? notes: 1. supported functions (y = supported; ? = not supported). qc, moh, pcm quick connect, modem-on-hold, pcm upstream tam telephone answering machine (voice playback and record through telephone line) fdsp full-duplex speakerphone and voice playback and record through telephone line, handset, and mic/speaker 2. for ordering purposes, the cx prefix may not be included in the part number for some devices. also, the cx prefix may not ap pear in the part number as branded on some devices. 3. lf = lead-free (pb-free) devices.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 1-3 figure 1-1. smartv.xx modem simplified interface diagram cx81801 modem 128-pin tqfp cx20493 smartdaa line side device (lsd) 28-pin qfn cx20442 voice codec (vc) 32-pin tqfp (optional) mic speaker tip ring telephone line interface discrete components 102199_001 digital isolation barrier (dib) tip ring handset (optional) telephone line (optional) parallel host bus or serial dte interface figure 1-2. smartv.xx modem major interfaces cx81801 modem 128-pin tqfp cx20442 voice codec (vc) 32-pin tqfp (optional) smartdaa interface modem data pump (mdp) digital speaker circuit (optional) paralle host or serial dte interface mic speaker 102199_002 sounducer hs hybrid components (optional) ram (32k x 8) rom (256k x 8) optional ram up to 1m (128k x 8) optional flash rom up to 4m (512k x 8) microcontroller unit (mcu) serial eeprom 2k (256 x 8) to 256k (32k x 8) (optional) tip ring telephone line interface discrete components tip ring voice relay, hs pickup detector (optional) telephone line telephone handset digital isolation barrier (dib) components cx20493 smartdaa line side device (lsd) 28-pin qfn line side dib interface (lsdi) codec telephone line interface daa hardware rectifier and filter components (mic/speaker) interface (optional)
cx81801-7x/8x smartv.xx modem data sheet 1-4 conexant 102199b 1.3 features 1.3.1 general modem features ? data modem ? quick connect, modem-on-hold, and pcm upstream functions (v.92 models) ? itu-t v.92/v.90 (v.92 models), v.34 (v.92 and v.34 models), v.32bis, v.32, v.29, fastpos (v.29), v.22 bis, v. 22, v.22 fast connect, v.23, v.21, bell 212a, and bell 103 ? v.250 and v.251 commands ? data compression and error correction ? v.44 data compression ? v.42 bis and mnp 5 data compression ? v.42 lapm and mnp 2-4 error correction ? fax modem send and receive rates up to 14.4 kbps ? v.17, v.29, v.27 ter, and v.21 channel 2 ? eia/tia 578 class 1 and t.31 class 1.0 ? v.80 synchronous acces s mode supports host-contro lled communication protocols with h.324 interface support ? interfaces to optional external rom/flas h rom, ram, and/or optional serial eeprom ? data/fax/voice call discrimination ? hardware-based modem controller ? hardware-based digital signal processor (dsp) ? worldwide operation ? complies to tbr21 and other country requirements ? on-hook and/or off-hook caller id detection for selected countries ? call progress, blacklisting ? internal rom includes default values for 29 countries ? additional and modified country profile can be stored in internal sram ? caller waiting detection ? caller id detect ? on-hook caller id detection ? off-hook call waiting caller id detection during data mode in v.92, v.90, v.34, v.32bis, and v.32 ? distinctive ring detect ? modem customization available through patch code that can be stored in optional serial eeprom or internal sram ? telephony/tam ? v.253 commands ? 2-bit and 4-bit conexant adpcm, 8-bit linear pcm, and 4-bit ima coding ? 8 khz sample rate ? concurrent dtmf, ring, and caller id detection
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 1-5 ? full-duplex speakerphone (fdsp) mode using optional cx20442 voice codec (s models) ? microphone and speaker interface ? telephone handset or headset interface ? acoustic and line echo cancellation ? microphone gain and muting ? speaker volume control and muting ? built-in hos t/dte interface ? parallel 16550a uart-compatible interface up to 230.4 kbps ? serial itu-t v.24 (eia/tia-232-e) logical interface up to 115.2 kbps ? downloadable architecture ? direct mode (serial dte interface) ? flow control and speed buffering ? automatic format/speed sensing ? serial async/sync data; parallel async data ? thin packages support low profile designs (1.6 mm max. height) ? cx81801 modem device in 128-pin tqfp ? cx20493 lsd in 28-pin qfn ? cx20442 vc in 32-pin tqfp ? +3.3v operation with +5v tolerant digital inputs ? typical power use ? cx81801 and cx20493: 209 mw (normal mode); 59 mw (sleep mode) ? cx20442: 5 mw (normal mode) 1.3.2 smartdaa features ? system side powered daa operates under poor line current supply conditions ? modem wake-on-ring ? ring detection ? line current loss detection ? pulse dialing ? line-in-use detection during on-hook operation ? remote hang-up detection for efficient call termination ? extension pickup detection ? digital pbx line protection ? meets worldwide dc voltage/current (vi) masks requirements 1.3.3 applications ? set top boxes ? gaming devices ? point of sale terminals ? remote monitoring and data collections systems ? handheld computers ? other embedded systems
cx81801-7x/8x smartv.xx modem data sheet 1-6 conexant 102199b 1.4 technical overview 1.4.1 general description modem operation, including dialing, call progress, telephone line interface, telephone handset interface, optional voice/speakerphone interface, and host interface functions are supported and controlled through the v.250, v.251, and v.253-compatible command set. the modem hardware connects to the host via a pa rallel or serial interface as selected by the parif input. the oem a dds a crystal circuit, dib components, telephone line interface, telephone handset/telephony extens ion interface, voice/sp eakerphone interface, optional external serial eeprom, optional external rom/flash rom, optional external ram, and other supporting discrete components as supported by the modem model (table 1-1) and required by the application to complete the system. customized modem firmware can be supported by the use of external memory in various combinations, e.g., either external rom/flas h rom (up to 256 kb), or external serial eeprom (256 to 32 kb) and external ram (up to 128 kb). to support country profile addition or modification, external serial eeprom (256 to 32 kb) can be installed. customized code can include oem-defined commands, i.e., identification codes (i3), identifier string (i4), manufacturer identification (+gmi), model identification (+gmm), and revision identification (+gmr), as well as code modification. parallel interface operation is selected by parif input high. serial interface operation is se lected by parif input low. 1.4.2 mcu firmware mcu firmware performs processing of general modem control, command sets, data modem, error correction and data compressi on (ecc), fax class 1, fax class 1.0, voice/audio/tam/speakerphone, worldwide, v.80 , and serial dte/parallel host interface functions according to modem models (table 1-1). mcu firmware can be customized to include oem-defined commands, i.e., identification codes (i3), identifier string (i4), manufacturer identification (+gmi), model identification (+gmm), and revision identification (+ gmr), as well as code modification. the modem firmware is provided in object code form for the oem to program into external rom/flash rom. the modem firmware may also be provided in source code form under a source code addendum license agreement. external rom/flash rom and ram must be installed in order to operate the modem with customized firmware. 1.4.3 operating modes 1.4.3.1 data/fax modes data modem modes perform complete hands hake and data rate negotiations. using modem modulations to optimize modem conf iguration for line conditions, the modem can connect at the highest data rate that the channel can support from 56 kbps down to 2400 bps with automatic fallback. in v.92/v.90 data modem modes (v.92 mode ls), the modem can receive data from a digital source using a v.92-compatible central site modem at line speeds up to 56 kbps. with pcm upstream enabled (v.92 only), data transmission supports sending data at line
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 1-7 speeds up to 48 kbps. when pcm upstream is disabled, data transmission supports sending data at line speeds up to v.34 rates. this mode can fallback to v.34 mode and to lower rates as dictated by line conditions. the following modes are supported in v.92 models when connected to a v.92- compatible server supporting the feature listed. ? quick connect: allows quicker subsequent connections to a server by using stored line parameters obtained during the initial connection. ? modem-on-hold: allows detection and reporting of incoming phone calls on the pstn with enabled call waiting. if the incoming call is accepted by the user, the user has a pre-defined amount of time of holding the data connection for a brief conversation. the data connection resumes upon incoming call termination. ? pcm upstream: boosts the upstream data rates. a maximum of 48 kbps is supported when connected to a v.92 server that supports pcm upstream. in v.34 data modem mode (v.92 and v.34 models), the modem can operate in full- duplex, asynchronous modes at line rates up to 33.6 kbps. automode operation in v.34 is provided in accordance with pn3320 and in v.32 bis in accordance with pn2330. all tone and pattern detection functions required by the applicable itu or bell standards are supported. in v.32 bis data modem mode, the modem can operate at line speeds up to 14.4 kbps. in fax modem mode, the modem can operate in half-duplex, synchronous modes and can support group 3 facsimile send and receive speeds of 14400, 12000 , 9600, 7 200, 4800, and 2400 bps. fax data transmission and reception performed by the modem are controlled and monitored through the eia/tia-578 fax class 1, or t.31 fax class 1.0 command interface. full hdlc formatting, zero insertion/deletion, and crc generation/checking are provided. 1.4.3.2 v.44 data compression v.44 provides efficient data compression that minimizes the download time for the types of files associated with internet use. this improvement is most no ticeable when browsing and searching the web since html text file s are highly compressible. (the improved performance amount varies both with the actual format and with the content of individual pages and files.) 1.4.3.3 worldwide operation smartdaa technology allows a single pcb design and single bom to be homologated worldwide. advanced features such as extension pickup detection, remote hang-up detection, line-in-use detection, and digital pbx detection are supported. country-dependent modem parameters for functions such as dialing, carrier transmit level, calling tone, call progress tone detection, answer tone detection, blacklisting, caller id, and relay control are programmable. country code ids are defined by itu-t t.35. embedded rom code includes default profiles for 29 countries. additional country profiles can be stored in internal sram or external serial eeprom (request additional country profiles from a conexant sales office). duplicate country profiles stored in internal sram or external serial eeprom will override the profiles in embedded rom code. the default countries supported are listed in table 1-2. country profiles for ctr-21 countries are tbr-21 compliant.
cx81801-7x/8x smartv.xx modem data sheet 1-8 conexant 102199b table 1-2. default countries supported country country code call waiting tone detection (cw) supported on-hook type 1 caller id (cid) supported off-hook type 2 called id (cid2) supported australia 09 x x austria 0a x x belgium 0f x brazil 16 x china 26 x x denmark 31 x x finland 3c x x france 3d x x x germany 42 x x hong kong 50 x x x india 53 x ireland 57 x italy 59 x x japan 00 x x x korea 61 x malaysia 6c x mexico 73 netherlands 7b x norway 82 x x poland 8a x portugal 8b x singapore 9c x x x south africa 9f x spain a0 x x sweden a5 x x switzerland a6 x taiwan fe x x united kingdom b4 x x x united states b5 x x x reserved fd x x x 1.4.3.4 tam mode tam mode features include 8-bit linear codi ng at 8 khz sample rate. tone detection/ generation, call discrimination, and concurrent dtmf detection are also supported. tam mode is supported by four submodes: ? online voice command mode supports connection to the telephone line or, for s models, a microphone/speaker/handset/headset. ? voice receive mode supports recording voice or audio data input from the telephone line or, for s models, a microphone/handset/headset. ? voice transmit mode supports playback of voice or audio data to the telephone line or, for s models, a speaker/handset/headset. ? full-duplex receive and transmit mode.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 1-9 1.4.3.5 speakerphone mode (s models) s models include additional telephone handset, external microphone, and external speaker interfaces which support voice and full-duplex speakerphone (fdsp) operation. hands-free full-duplex telephone operation is supported in speakerphone mode under host control. speakerphone m ode features an advanced proprietary speakerphone algorithm which supports full-duplex voice conversation with acoustic, line, and handset echo cancellation. parameters are constantly adjusted to maintain stability with automatic fallback from full-duplex to pseudo-duple x operation. the sp eakerphone algorithm allows position independent placement of microphone and speaker. the host can separately control volume, muting, and agc in microphone and speaker channels. 1.4.4 reference designs a data/fax/tam/speakerphone reference design for external modems is available to minimize application design time, reduce deve lopment cost, and acceler ate market entry. this designs is: ? for cx81801 and cx20493: rd01-d660-1xx a design package is available in electronic form. this package includes schematics, bill of materials (bom), vendor part list (vpl), board layout files in gerber format, and complete documentation. 1.5 hardware description smartdaa technology eliminates the need for a costly analog transformer, relays, and opto-isolators that are typically used in discrete daa implementations. the programmable smartdaa architecture simplif ies product implementation in worldwide markets by eliminating the need for country-specific components. 1.5.1 cx81801 modem device the cx81801 modem, packaged in a 128-pin tqfp, includes a microcontroller (mcu), a modem data pump (mdp), 256 kb inte rnal rom, 32 kb internal ram, and smartdaa interface functions. the cx81801 modem connects to host via a parallel host (parif = high) or a logical v.24 (eia/tia-232-e) serial dte interface (parif = low). the cx81801 modem performs the command processing an d host interface functions. the crystal frequency is 28.224 mhz 50 ppm. the cx81801 modem optionally connects to an external oem-supplied serial eeprom over a dedicated 2-line serial interface. the capacity of the eeprom can be 256 bytes up to 32 kb. the eeprom can hold information such as firmware configuration customization, and country code parameters. the cx81801 modem performs telephone line signal modulation/demodulation in a hardware digital signal processor (dsp) which reduces computational load on the host processor. the smartdaa interface communicates with, an d supplies power and clock to, the lsd through the dib.
cx81801-7x/8x smartv.xx modem data sheet 1-10 conexant 102199b the cx81801 optionally connects to extern al oem-supplied rom/flash rom and ram over a non-multiplexed 19-bit address bus and 8-bit data bus. 1.5.2 digital isolation barrier the oem-supplied digital isolation barrier (d ib) electrically dc isolates the cx81801 from the lsd and telephone line. the modem is connected to a fixed digital ground and operates with standard cmos logic levels. the lsd is connected to a floating ground and can tolerate high voltage input (compatible with telephone line and typical surge requirements). the dib transformer couples power and clock from the cx81801 to the lsd. the dib data channel supports bidirectional half-duplex serial transfer of data, control, and status information between the cx81801 and the lsd over two lines. 1.5.3 cx20493 smartdaa line side device the cx20493 smartdaa line side device (lsd) includes a line side dib interface (lsdi), a coder/decoder (codec), and a telephone line interface (tli). the lsdi communicates with, and receive s power and clock from, the smartdaa interface in the cx81801 through the dib. lsd power is received from the mdp pwrclkp and pwrclkn pins via the dib through a full-wave rectified bridge and cap acitive power filter circuit connected to the dib transformer secondary winding. the clk input is also accepted from the di b transformer secondary winding through a capacitor and a resistor in series. information is transferred between the ls d and the cx81801 through the dib_p and dib_n pins. these pins connect to the cx81801 dib_datap and dib_datan pins, respectively, through the dib. the tli integrates daa and direct teleph one line interface functions and connects directly to the line tip and ring pins, as well as to external line protection components. direct lsd connection to tip and ring allo ws real-time measurem ent of telephone line parameters, such as the telephone centra l office (co) battery voltage, individual telephone line (copper wire) resistance, and allows dynamic regulation of the off-hook tip and ring voltage and total current drawn from the central office (co). this allows the modem to maintain compliance with u.s. and worldwide regulations and to actively control the daa power dissipation. 1.5.4 cx20442 voice codec the optional cx20442 voice codec (vc), packaged in a 32-pin tqfp, supports voice/full-duplex speakerphone (fdsp) opera tion with interfaces to a microphone and speaker and to a telephone handset/headset. 1.6 at commands the smartv.xx modem supports at commands for data mode, fax class 1 or 1.0, voice/audio, full-duplex speakerphone (fdsp), v.80 commands, and s register. see doc. no. 102184 for a description of the commands.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 1-11 data mode operation. data functions operate in response to the at commands when +fclass=0. default parameters support u.s./canada operation. fax mode operation. facsimile functions operate in response to fax class 1 commands when +fclass=1 or to fax class 1.0 commands when +fclass=1.0. voice/audio operation. voice/audio functions operate in response to voice/audio commands when +fclass=8. speakerphone operation. fdsp functions operate in response to speakerphone commands when +fclass=8 and +vsp=1 is selected.
cx81801-7x/8x smartv.xx modem data sheet 1-12 conexant 102199b this page is intentionally blank.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 2-1 2. technical specifications 2.1 serial dte interface operation 2.1.1 automatic speed/format sensing command mode and data mode. the modem can automatically determine the speed and format of the data sent from the dte. the modem can sense speeds of 300, 600, 1200, 2400, 4800, 7200, 9600, 12000, 14400, 16800, 19200, 21600, 24000, 26400, 28800, 38400, 57600, and 115200 bps and the following data formats: parity data length (no. of bits) no. of stop bits character length (no. of bits) none 7 2 10 odd 7 1 10 even 7 1 10 none 8 1 10 odd 8 1 11* even 8 1 11* *11-bit characters are sensed, but the parity bit is stripped off during data transmission in normal and error correction modes. the modem can speed sense data with mark or space parity and configures itself as follows: dte configuration modem configuration 7 mark 7 none 7 space 8 none 8 mark 8 none 8 space 8 even fax mode. in v.17 fax mode, the modem can sense speeds up to 115.2 kbps.
cx81801-7x/8x smartv.xx modem data sheet 2-2 conexant 102199b 2.2 parallel host bus interface operation command mode and data mode. the modem can operate at rates up to 230.4 kbps by programming the divisor latch in the parallel interface registers if supported by communications software and/or driver. fax mode. in v.17 mode, the modem can operat e at rates up to 230.4 kbps by programming the divisor latch in the parallel interface registers if supported by communications software and/or driver. 2.3 establishing data modem connections 2.3.1 dialing dtmf dialing. dtmf dialing using dtmf tone pairs is supported in accordance with itu-t q.23. the transmit tone level complies with bell publication 47001. pulse dialing. pulse dialing is supported in accordance with eia/tia-496-a. blind dialing. the modem can blind dial in the absence of a dial tone if enabled by the x0, x1, or x3 command. 2.3.2 telephone number directory the modem supports four telephone number entries in a directory that can be saved in a serial eeprom. each telephone number can be up to 32 characters (including the command line terminating carriage return) in length. a telephone number can be saved using the &zn=x command, and a saved telephone number can be dialed using the ds=n command. 2.3.3 modem handshaking protocol if a tone is not detected within the time specified in the s7 register after the last digit is dialed, the modem aborts the call attempt. 2.3.4 call progress tone detection ringback, equipment busy, congested tone, warble tone, and progress tones can be detected in accordance with the applicable standard. 2.3.5 answer tone detection answer tone can be detected over the frequency range of 2100 40 hz in itu-t modes and 2225 40 hz in bell modes. 2.3.6 ring detection a ring signal can be detected from a ttl-co mpatible 15.3 hz to 68 hz square wave input.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 2-3 2.3.7 billing protection when the modem goes off-hook to answer an incoming call, both transmission and reception of data are prevented for 2 seconds (data modem) or 4 seconds (fax adaptive answer) to allow transmission of the billing tone signal. 2.3.8 connection speeds the modem functions as a data modem when the +fclass=0 command is active. line connection can be selected using th e +ms command. the +ms command selects modulation, enables/disables automode, and selects minimum and maximum line speeds (table 2-1). 2.3.9 automode automode detection can be enabled by the +ms command to allow the modem to connect to a remote modem in accordance w ith draft pn-3320 for v.34 (table 2-1). table 2-1. +ms command automode connectivity modulation possible (, , (), and ) rates (bps) bell 103 b103 300 bell 212 b212 1200 rx/75 tx or 75 rx/1200 tx v.21 v21 300 v.22 v22 1200 v.22 bis v22b 2400 or 1200 v.23 v23c 1200 v.32 v32 9600 or 4800 v.32 bis v32b 14400, 12000, 9600, 7200, or 4800 v.34 v34 33600, 31200, 28800, 26400, 24000, 21600, 19200, 16800, 14400, 12000, 9600, 7200, 4800, or 2400 v.90 v90 56000, 54667, 53333, 52000, 50667, 49333, 48000, 46667, 45333, 44000, 42667, 41333, 40000, 38667, 37333, 36000, 34667, 33333, 32000, 30667, 29333, 28000 v.92 downstream v92 56000, 54667, 53333, 52000, 50667, 49333, 48000, 46667, 45333, 44000, 42667, 41333, 40000, 38667, 37333, 36000, 34667, 33333, 32000, 30667, 29333, 28000 v.92 upstream v92 48000, 46667, 45333, 44000, 42667, 41333, 40000, 38667, 37333, 36000, 34667, 33333, 32000, 30667, 29333, 28000, 26667, 25333, 24000
cx81801-7x/8x smartv.xx modem data sheet 2-4 conexant 102199b 2.4 data mode the modem enters data mode when a telephone line connection has been established between modems and all handshaking has been completed. 2.4.1 speed buffering (normal mode) speed buffering allows a dte to send data to , and receive data from, a modem at a speed different than the line speed. the modem s upports speed bufferin g at all line speeds. 2.4.2 flow control dte-to-modem flow control. if the modem-to-line speed is less than the dte-to- modem speed, the modem supports xoff/xon or rts/cts flow control with the dte to ensure data integrity. 2.4.3 escape sequence detection the +++ escape sequence can be used to retu rn control to the command mode from the data mode. escape sequence detection is disabled by an s2 register value greater than 127. 2.4.4 break detection the modem can detect a break signal from e ither the dte or the remote modem. the \kn command determines the modem response to a received break signal. 2.4.5 telephone line monitoring gstn cleardown (v.90, v.34, v.32 bis, v.32). upon receiving gstn cleardown from the remote modem in a non-error correcting m ode, the modem cleanly terminates the call. loss of carrier (v.22 bis and below). if carrier is lost for a time greater than specified by the s10 register, the modem disconnects. 2.4.6 fall forward/fallback (v.92/ v.90/v.34/v.32 bis/v.32) during initial handshake, the modem will fallback to the optimal line connection within v.92/v.90/v.34/v.32 bis/v.32 mode depending upon signal quality if automode is enabled by the +ms or n1 command. when connected in v.92/v.90/v.34/v.32 bis/v.32 mode, the modem will fall forward or fallback to the optimal line speed within the current modulation depending upon signal quality if fall forward/fallback is enabled by the %e2 command.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 2-5 2.4.7 retrain the modem may lose synchronization with the received line signal under poor or changing line conditions. if this occurs, retraining may be initiated to attempt recovery depending on the type of connection. the modem initiates a retrain if line quality b ecomes unacceptable if enabled by the %e command. the modem continues to retrain until an acceptable connection is achieved, or until 30 seconds elapse resulting in line disconnect. 2.4.8 programmable inactivity timer the modem disconnects from the line if data is not sent or received for a specified length of time. in normal or error-correction mode, this inactivity timer is reset when data is received from either the dte or from the line. this timer can be set to a value between 0 and 255 seconds by using register s30. a value of 0 disables the inactivity timer. 2.4.9 dte signal monitoring (serial dte interface only) dtr#. when dtr# is asserted, the modem re sponds in accordance with the &dn and &qn commands. rts#. rts# is used for flow control if enabled by the &k command in normal or error- correction mode. 2.5 v.92 features modem-on-hold, quick connect, and pcm upstream are only available in v.92 models when connecting in v.92 data mode. v.92 f eatures are only available when the server called is a v.92 server that supports that particular feature. 2.5.1 modem-on-hold the modem-on-hold (moh) function enables the modem to place a data call to the internet on hold while using the same lin e to accept an incoming or place an outgoing voice call. this feature is available only with a connection to a server supporting moh. moh can be executed through either of two methods: ? one method is to enable moh through the +pmh command. with call waiting detection (+pcw command) enabled, an in coming call can be detected while on- line. using a string of commands, the mode m negotiates with the server to place the data connection on hold while the line is released so that it can be used to conduct a voice call. once the voice call is completed, the modem can quickly renegotiate with the server back to the original data call. ? an alternative method is to use communicati ons software that utilizes the conexant modem-on-hold drivers under windows pc operating systems. using this method, the software can detect an incoming call, place the data connection on hold, and switch back to a data connection.
cx81801-7x/8x smartv.xx modem data sheet 2-6 conexant 102199b 2.5.2 quick connect the quick connect function enables the modem to shorten the connect time of subsequent calls to a server supporting quick connect. th e quick connect feature is supported by the +pqc command. 2.5.3 pcm upstream pcm upstream boosts the upstream data rate s between the user and isp to reduce upload times for large files and email attachments. a maximum of 48 kbps upstream rate is supported with pcm upstream enabled, in contrast to a maximum of 32.2 kbps upstream rate with pcm upstream not enabled. pcm upst ream is supported by the +pig command. pcm upstream is disabled by default. 2.6 error correction and data compression 2.6.1 v.42 error correction v.42 supports two methods of error correction: lapm and, as a fallback, mnp 4. the modem provides a detection and negotiation technique for determining and establishing the best method of error correction between two modems. 2.6.2 mnp 2-4 error correction mnp 2-4 is a data link protocol that uses error correction algorithms to ensure data integrity. supporting stream mode, the modem sends data frames in varying lengths depending on the amount of time between characters coming from the dte. 2.6.3 v.44 data compression v.44 data compression mode, enabled by the +ds44 command, encodes pages and files associated with web pages. these files incl ude web pages, graphics and image files, and document files. v.44 can provide an effective data throughput rate up to dte rate for a 56-kbps connection. the improved performance amount varies both with the actual format and with the content of individual pages and files. 2.6.4 v.42 bis data compression v.42 bis data compression mode, enabled by the %cn command or s46 register, operates when a lapm connection is established. the v.42 bis data compression employs a ?strin g learning? algorithm in which a string of characters from the dte is encoded as a fixe d length codeword. two 2-kb dictionaries are used to store the strings. these dictionaries are dynamically updated during normal operation.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 2-7 2.6.5 mnp 5 data compression mnp 5 data compression mode, enabled by the %cn command, operates during an mnp connection. in mnp 5, the modem increases its throughput by compressing data into tokens before transmitting it to the remote modem, and by decompressing encoded received data before sending it to the dte. 2.7 telephony extensions the following telephony extension features are supported and are typically implemented in designs for set-top box applications and tam software applications to enhance end- user experience: ? line in use detection ? extension pickup detection ? remote hang-up detection the telephony extension features are enab led through the -ste command. the -tte command can be used to adjust the voltage thresholds for the telephony extension features. 2.7.1 line in use detection the line in use detection feature can stop the modem from disturbing the phone line when the line is already being used. when an automated system tries to dial using atdt and the phone line is in use, the modem will not go off hook and will respond with the message ?line in use?. in the case where no phone line is connected to the modem, the modem will respond with the message ?no line?. 2.7.2 extension pickup detection the extension pickup detection feature (a lso commonly referred as ppd or parallel phone detection) allows the modem to detect when another telephony device (i.e., fax machine, phone, satellite/cable box) is a ttempting to use the phone line. when an extension pickup has been detected, the modem will go on-hook and respond with the message ?off-hook intrusion?. the remote hangup detection feature will cause the modem to go back on-hook and respond with the message ?line reversal detected? during a data connection when the remote modem is disconnected for abnormal termination reasons (remote phone line unplugged, remote server/modem shutdown). for voice applications, this method can be used in addition to silence detection to determine when a remote caller has hung up to terminate a voice recording. this feature can be used to quickly drop a modem connection in the event when a user picks up a extension phone line. for example, this feature allows set top boxes with an integrated smartv.xx modem to give normal voice users the highest priority over the telephone line. this feature can also be used in telephone answering machine applications (tam). its main use would be to stop the tam operation when a phone is picked up.
cx81801-7x/8x smartv.xx modem data sheet 2-8 conexant 102199b 2.7.3 remote hangup detection the remote hangup detection feature will cause the modem to go back on-hook and respond with the message ?line revers al detected? during a data connection when the remote modem is disconnected for abnormal termination reasons (remote phone line unplugged, remote server/modem shutdown). for voice applications, this method can be used in addition to silence detection to determine when a remote caller has hung up to terminate a voice recording. 2.8 fax class 1 and fax class 1.0 operation facsimile functions operate in response to fax class 1 commands when +fclass=1 or to fax class 1.0 commands when +fclass=1.0. in the fax mode, the on-line behavior of the modem is different from the data (non-fax) mode. after dialing, modem operation is controlled by fax commands. some at commands are still valid but may operate differently than in data modem mode. calling tone is generated in accordance with t.30. 2.9 point-of-sales support point-of-sales (pos) terminals usually need to exchange a small amount of data in the shortest amount of time. low speed modula tions such as bell212a or v.22 are still mainly used in pos applications. additionally, new non-standard sequences have been developed to better support pos applications. industry standard and shortened answer tone b103 and v.21 are supported, as well as fastpos (v.29) and v.22 fast connect. pos terminal modulations are supported by the $f command. 2.10 voice/audio mode voice and audio functions are supported by the voice mode. voice mode includes four submodes: online voice command mode, voi ce receive mode, voice transmit mode and full-duplex receive and transmit mode. 2.10.1 online voice command mode this mode results from the connection to the telephone line or a voice/audio i/o device (e.g., microphone, speaker, or handset) through the use of the +fclass=8 and +vls commands. after mode entry, at commands can be entered without aborting the connection. 2.10.2 voice receive mode this mode is entered when the +vrx command is active in order to record voice or audio data input at the rin pin, typically from a microphone/handset or the telephone line. received analog voice samples are converted to digital form and compressed for reading by the host. at commands control the codec bits-per-sample rate.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 2-9 received analog mono audio samples are conver ted to digital form and formatted into 8- bit unsigned linear pcm format for reading by the host. at commands control the bit length and sampling rate. concurrent dtmf/tone detection is available at the 8 khz sample rate. 2.10.3 voice transmit mode this mode is entered when the +vtx command is active in order to playback voice or audio data to the txa output, typically to a speaker/handset or to the telephone line. digitized voice data is decompressed and co nverted to analog form at the original compression quantization sample-per-bits rate then output to the txa output. digitized audio data is converted to analog form then output to the txa output. 2.10.4 full-duplex receive and transmit mode this mode is entered when the +vtr command is active in order to concurrently receive and transmit voice. 2.10.5 audio mode the audio mode enables the host to transmit an d receive 8-bit audio signals. in this mode, the modem directly accesses the internal anal og-to-digital (a/d) co nverter (adc) and the digital-to-analog (d/a) converter (dac). incoming analog audio signals can then be converted to digital format and digital signals can be converted to analog audio output. 2.10.6 tone detectors the tone detector signal path is separate from the main received signal path thus enabling tone detection to be independent of the configuration status. in tone mode, all three tone detectors are operational. 2.10.7 speakerphone mode speakerphone mode is controlled in voice mode with the following commands: use speakerphone after dia ling or answering (+vsp=1). +vsp=1 selects speakerphone mode while in +fclass=8 mode. speakerphone operation is entered during voice online command mode after completing dialing or answering. speakerphone settings. the +vgm and +vgs commands can be used to control the microphone gain and speaker volume, respectively. vgm and +vgs commands are valid only after the modem has entered the voice online mode while in the +vsp=1 setting. 2.11 v.80 synchronous access mode (sam) - video conferencing v.80 synchronous access mode between the modem and the host/dte is provided for host-controlled communication protocols, e.g., h.324 video conferencing applications. voice-call-first (vcf) before switching to a videophone call is also supported.
cx81801-7x/8x smartv.xx modem data sheet 2-10 conexant 102199b 2.12 full-duplex speakerphone (fds p) mode (s models) the modem operates in fdsp mode when +fclass=8 and +vsp=1 (section 2.10.7). in fdsp mode, speech from a microphone or handset is converted to digital form, shaped, and output to the telephone line through the line interface circuit. speech received from the telephone line is shaped, co nverted to analog form, and output to the speaker or handset. shaping includes bo th acoustic and line echo cancellation. 2.13 caller id both type i caller id (on-hook caller id) and type ii caller id (call waiting caller id) are supported for u.s. and many other countries (see section 2.14). both types of caller id are enabled/disabled using the +vcid command. call waiting tone detection must be enabled using the +pcw command to detect and decode call waiting caller id. when enabled, caller id information (date, time, caller code, and name) can be passed to the dte in formatted or unformatted form. inquiry support allows the current caller id mode and mode capabilities of the modem to be retrieved from the modem. type ii caller id (call waiting caller id) detection operates only during data mode in v.92, v.90, v.34, v.32bis, or v.32. 2.14 worldwide country support internal modem firmware supports 29 countr y profiles (see section 1.3.2). these country profiles include the following country-dependent parameters: ? dial tone detection levels and frequency ranges. ? dtmf dialing parameters: transmit output level, dtmf signal duration, and dtmf interdigit interval. ? pulse dialing parameters: make/break times, set/clear times, and dial codes are programmable ? ring detection frequency range. ? type i and type ii caller id detection are supported for many countries. contact your local conexant sales office for additional country support. ? blind dialing enabled/disable. ? carrier transmit level (through s91 for data and s92 for fax). the maximum, minimum, and default values can be defined to match specific country and daa requirements. ? calling tone is generated in accordance with v.25. calling tone may be toggled (enabled/disabled) by inclusion of a ?^? ch aracter in a dial string. it may also be disabled. ? frequency and cadence of tones for busy, ringback, congested, warble, dial tone 1, and dial tone 2. ? answer tone detection period.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 2-11 ? blacklist parameters. the modem can operate in accordance with requirements of individual countries to prevent misuse of the network by limiting repeated calls to the same number when previous call attempts have failed. call failure can be detected for reasons such as no dial t one, number busy, no answer, no ringback detected, voice (rather than modem) detect ed, and key abort (dial attempt aborted by user). actions resulting from such failures can include specification of minimum inter-call delay, extended delay between calls, and maximum numbers of retries before the number is permanently forbidden ("blacklisted"). these country profiles may be altered or customized by modifying the country-dependent parameters. additional profiles may also be included. there are two ways to add or modify profiles: ? incorporating additional or modified profiles into external flash rom containing the entire modem firmware code. ? linking additional or modified profiles from an external serial eeprom (needed only if the external flash rom capacity is exceeded. please contact an fae at the local conexant sales office if a country code customization is required. 2.15 diagnostics 2.15.1 commanded tests diagnostics are performed in response to test commands. analog loopback (&t1 command). data from the local dte is sent to the modem, which loops the data back to the local dte. dtmf generation (%tt0 command). continuous dtmf tones are generated by the dsp and output through the daa. tone generation (%tt3 command). continuous tones are generated by the dsp and output through the daa. 2.15.2 power on reset tests upon power on, the modem performs tests of the modem and internal ram. if the modem or internal ram test fails, the tmind# output is pulsed as follows (figure 2-1): ? internal ram test fails: one pulse cycle ( pulse cycle = 0.5 sec. on, 0.5 sec. off) every 1.5 seconds. ? modem device test fails: three pulse cycles every 1.5 seconds.
cx81801-7x/8x smartv.xx modem data sheet 2-12 conexant 102199b figure 2-1. tmind# test results pulse cycles 102179_004 0 .5 11.522.533.544.55 internal ram fails 0 .5 11.522.533.544.55 modem device fails 5.5 5.566.57 pulse cycle pulse cycle 1.5 sec 1.5 sec 2.16 low power sleep mode sleep mode entry. the modem enters the low power sleep mode when no line connection exists and no host activity occurs for the period of time specified in the s24 register. all modem circuits are turned off ex cept the internal clock circuitry in order to consume reduced power while being able to immediately wake up and resume normal operation. wake-up. wake-up occurs when a ring is detected on the telephone line, the host writes to the modem (parallel interface), or the dte sends a character to the modem (serial interface).
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-1 3. hardware interface 3.1 cx81801 modem hardware pins and signals 3.1.1 common to parallel and seria l interface configurations 3.1.1.1 lsd interface (through dib) the dib interface signals are: ? clock and power positive (pwrclkp); output ? clock and power negative (pwrclkn); output ? data positive (dib_datap); input/output ? data negative (dib_datan); input/output 3.1.1.2 call progress speaker interface the call progress speaker interface signal is: ? digital speaker output (dspkout); output dspkout is a square wave output in data/fax mode used for call progress or carrier monitoring. this output can be optionally connected to a low-cost on-board speaker, e.g., a sounducer, or to an an alog speaker circuit. 3.1.1.3 voice relay interface (s models) the voice relay interface signal is: ? voice relay control (voice#); output 3.1.1.4 serial eeprom interface a 2-line serial interface to an optional seri al eeprom is supported. the interface signals are: ? bidirectional data input/output (nvmdata) ? clock output (nvmclk) the eeprom can hold information such as firmware customization, and country code parameters. data stored in eeprom takes precedence over the factory default settings. note: this information is usually stored in flash rom; serial eeprom is required only if storage is required for more than 31 country profiles. the eeprom size can range from 2 kb (256 x 8) to 256 kb (32k x 8). a 2 kb eeprom must be 100 khz or 400 khz; higher capacity eeproms must be 400 khz.
cx81801-7x/8x smartv.xx modem data sheet 3-2 conexant 102199b 3.1.1.5 external bus interface the external bus optionally connects to oem-supplied external memory: ? up to 4 mb (512k x 8) rom/flash rom ? up to 1 mb (128k x 8) ram the non-multiplexed external bus interface signals are: ? eight bidirectional data lines (d0-d7) ? 19 address output lines (a0-a18) ? read enable output (read#) ? write enable output (write#) ? rom chip select output (romsel#) ? ram chip select output (ramsel#) 3.1.2 serial interface configuration only 3.1.2.1 serial dte interface and indicator outputs (parif = low) a v.24/eia/tia-232-e logic-compatible seri al dte interface is selected when the parif input is low. the supported dte interface signals are: ? serial transmit data input (txd#) ? serial receive data output line (rxd#) ? clear to send output (cts#) ? data set ready output (dsr#) ? received line signal detector (rlsd#) ? test mode output (tm#) ? ring indicator (ri#) ? data terminal ready control input (dtr#) ? request to send control input (rts#) additional clock signals provided for synchronous mode are: ? receive data clock (rxclk#) ? transmit data clock (txclk#) ? external clock (xtclk#) the following indicator outpu t lines are also supported: ? auto answer indicator output (aaind#) ? data terminal ready in dicator output (dtrind#) ? test mode indicator output (tmind#) ? off-hook indicator output (ohind#)
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-3 3.1.3 parallel interface configura tion only (parif = high) a 16550a uart-compatible parallel host bus interface is select ed when the parif input is high. 3.1.3.1 parallel host bus interface the parallel host interface signals are: ? host reset control input line (reset#) ? host chip select control input (hcs#) ? host read control input (hrd#) an d host write control input (hwt#) ? host interrupt output line (hint) ? three host address input lines (ha0-ha2) ? eight host data lines (hd0-hd7) 3.1.4 cx81801 modem interface signals cx81801 modem 128-pin tqfp hardware in terface signals for parallel interface are shown by major interface in figure 3-1, are sh own by pin number in figure 3-2, and are listed by pin number in table 3-1. the smart modem hardware interface signals for parallel interface are defined in table 3-2. cx81801 modem 128-pin tqfp hardware interf ace signals for serial interface are shown by major interface in figure 3-3, are shown by pin number in figure 3-4, and are listed by pin number in table 3-3. cx81801 mode m hardware interface signals for serial interface are defined in table 3-4. i/o types are defined in table 3-5. dc electrical characteristics are listed in table 3-6.
cx81801-7x/8x smartv.xx modem data sheet 3-4 conexant 102199b figure 3-1. cx81801 modem hardware signals for parallel interface (parif = high) xtli xtlo clkin clkout xclk dv1tp lpo noxyck parif stpmode# (pd3) nmi# reset# hcs# (pd4) hrd# (pd6) hwt# (pd5) hint (pb7) ha0 (pd0) ha1 (pd1) ha2 (pd2) hd0 (pc0) hd1 (pc1) hd2 (pc2) hd3 (pc3) hd4 (pc4) hd5 (pc5) hd6 (pc6) hd7 (pc7) reserved (pa0) reserved (pe6) reserved (pa1) testp phs2 sr4in pd7 reserved (pa2) reserved (pa6) reserved (pb1) reserved (p_pa00) reserved (p_pa04) reserved (p_pa05) reserved (p_pb01) reserved (bd2clk) reserved (p_gp00) p_px00 p_px02 p_px03 vgg vdd vdd vdd vdd vdd vdd vdd vdd vdd vdd_core vdd_core vdd_core gnd gnd gnd gnd gnd gnd gnd gnd gnd gnd gnd gnd 114 115 113 61 49 111 57 47 5 9 117 34 11 13 12 109 6 7 8 122 123 125 126 127 1 3 4 24 22 26 110 121 45 46 27 32 101 55 54 56 51 59 52 41 42 43 60 2 15 40 58 78 100 108 116 124 20 53 85 10 25 30 44 48 68 90 95 103 112 120 128 host parallel bus line_sel (pe7) reserved (pa5) reserved (pa4) reserved (pe5) reserved (pe2) reserved (pa3) reserved (pe0) voice# (pe1) hs_lcs (pe4) dspkout pwrclkp pwrclkn dib_datap dib_datan iasleep (p_pf05) m_clk (p_pb00) sr2clk (p_pgp05) sa2clk (p_px05) sr3out sr3in (p_px01) sr2io (p_px06) nvmclk (pa7) nvmdata (pe3) a0 a1 a2 a3 a4 a5 a6 a7 a8 a9 a10 a11 a12 a13 a14 a15 a16 (pb0) a17 (pb4) a18 (pb5) d0 d1 d2 d3 d4 d5 d6 d7 write# read# romsel# (pb2) ramsel# (pb3) ext_res# (pb6) pllvdd pllgnd 23 31 29 21 17 28 14 16 19 98 96 97 93 94 50 37 92 38 35 36 39 33 18 71 72 73 74 75 76 77 79 80 81 84 86 87 88 89 91 99 105 106 62 63 64 65 66 67 69 70 118 119 102 104 107 82 83 eeprom (optional) 102199_003 +3.3v cx81801 smart modem 128-pin tqfp parallel interface (parif = high) +3.3v digital isolation barrier (dib) 0.1 uf nc +3.3v nc crystal circuit nc external memory +3.3v nc speaker circuit nc nc +3.3v cx20442 voice codec (vc) (optional) sleep m_clkin m_sck m_strobe m_txsin m_rxout m_cntrlsin +3.3v or +5v voice# hs_lcs 240k nc daa 47k 47k 47k nc nc nc +3.3v +3.3v nc
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-5 figure 3-2. cx81801 modem 128-pin tqfp pin signals for parallel interface (parif = high) 102199_004 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 4 0 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 5 0 5 1 5 2 5 3 5 4 5 5 5 6 5 7 5 8 5 9 6 0 6 1 6 2 6 3 6 4 1 0 2 1 0 1 1 0 0 9 9 9 8 9 7 9 6 9 5 9 4 9 3 9 2 9 1 9 0 8 9 8 8 8 7 8 6 8 5 8 4 8 3 8 2 8 1 8 0 7 9 7 8 7 7 7 6 7 5 7 4 7 3 7 2 7 1 7 0 6 9 6 8 6 7 6 6 6 5 1 2 8 1 2 7 1 2 6 1 2 5 1 2 4 1 2 3 1 2 2 1 2 1 1 2 0 1 1 9 1 1 8 1 1 7 1 1 6 1 1 5 1 1 4 1 1 3 1 1 2 1 1 1 1 1 0 1 0 9 1 0 8 1 0 7 1 0 6 1 0 5 1 0 4 1 0 3 g n d h d 4 ( p c 4 ) h d 3 ( p c 3 ) h d 2 ( p c 2 ) v d d h d 1 ( p c 1 ) h d 0 ( p c 0 ) p h s 2 g n d r e a d # w r i t e # n m i # v d d x t l o x t l i c l k i n g n d d v 1 t p t e s t p h i n t ( p b 7 ) v d d e x t _ r e s # ( p b 6 ) a 1 8 ( p b 5 ) a 1 7 ( p b 4 ) r a m s e l # ( p b 3 ) g n d s r 2 i o ( p _ p x 0 6 ) v d d p _ p x 0 0 p _ p x 0 2 p _ p x 0 3 g n d s r 4 i n p d 7 n o x y c k g n d x c l k i a s l e e p ( p _ p f 0 5 ) r x c l k ( p _ p b 0 1 ) x t c l k ( g p 0 0 ) v d d _ c o r e t x c l k ( p _ p a 0 4 ) r e s e r v e d ( p _ p a 0 0 ) r e s e r v e d ( p _ p a 0 5 ) l p o v d d r e s e r v e d ( b d 2 c l k ) v g g c l k o u t d 0 d 1 d 2 r o m s e l # ( p b 2 ) r e s e r v e d ( p b 1 ) v d d a 1 6 ( p b 0 ) d s p k o u t p w r c l k n p w r c l k p g n d d i b _ d a t a n d i b _ d a t a p s r 2 c l k ( p _ p g p 0 5 ) a 1 5 g n d a 1 4 a 1 3 a 1 2 a 1 1 v d d _ c o r e a 1 0 p l l g n d p l l v d d a 9 a 8 a 7 v d d a 6 a 5 a 4 a 3 a 2 a 1 a 0 d 7 d 6 g n d d 5 d 4 d 3 h d 5 ( p c 5 ) v d d h d 6 ( p c 6 ) h d 7 ( p c 7 ) p a r i f h a 0 ( p d 0 ) h a 1 ( p d 1 ) h a 2 ( p d 2 ) s t p m o d e # ( p d 3 ) g n d h c s # ( p d 4 ) h w t # ( p d 5 ) h r d # ( p d 6 ) r e s e r v e d ( p e 0 ) v d d v o i c e # ( p e 1 ) r e s e r v e d ( p e 2 ) n v m d a t a ( p e 3 ) h s _ l c s ( p e 4 ) v d d _ c o r e r e s e r v e d ( p e 5 ) r e s e r v e d ( p e 6 ) l i n e _ s e l ( p e 7 ) r e s e r v e d ( p a 0 ) g n d r e s e r v e d ( p a 1 ) r e s e r v e d ( p a 2 ) r e s e r v e d ( p a 3 ) r e s e r v e d ( p a 4 ) g n d r e s e r v e d ( p a 5 ) r e s e r v e d ( p a 6 ) n v m c l k ( p a 7 ) r e s e t # s r 3 o u t s r 3 i n ( p _ p x 0 1 ) m _ c l k ( p _ p b 0 0 ) s a 2 c l k ( p _ p x 0 5 ) cx81801 parallel interface (parif pin = high)
cx81801-7x/8x smartv.xx modem data sheet 3-6 conexant 102199b table 3-1. cx81801 modem 128-pin tqfp pin signals for parallel interface (parif = high) pin signal label i/o i/o type interface pin signal label i/o i/o type interface 1 hd5 (pc5) i/o ith/ot8 hb: hd5 65 d3 i/o ith/ot2 eb: d3 2 vdd p pwr +3.3v 66 d4 i/o ith/ot2 eb: d4 3 hd6 (pc6) i/o ith/ot8 hb: hd6 67 d5 i/o ith/ot2 eb: d5 4 hd7 (pc7) i/o ith/ot8 hb: hd7 68 gnd g gnd gnd 5 parif i itpu nc (parallel interface) 69 d6 i/o ith/ot2 eb: d6 6 ha0 (pd0) i ithpd/ot2 hb: ha0 70 d7 i/o ith/ot2 eb: d7 7 ha1 (pd1) i ithpd/ot2 hb: ha1 71 a0 o it/ot8 eb: a0 8 ha2 (pd2) i ithpd/ot2 hb: ha2 72 a1 o it/ot8 eb: a1 9 stpmode# (pd3) i ith/ot2 nc 73 a2 o it/ot8 eb: a2 10 gnd g gnd gnd 74 a3 o it/ot8 eb: a3 11 hcs# (pd4) i it hb: cs# 75 a4 o it/ot8 eb: a4 12 hwt# (pd5) i ithpu hb: wt# 76 a5 o it/ot8 eb: a5 13 hrd# (pd6) i ithpu hb: rd# 77 a6 o it/ot8 eb: a6 14 reserved (pe0) o it/ot8 nc 78 vdd p pwr +3.3v 15 vdd p pwr +3.3v 79 a7 o it/ot8 eb: a7 16 voice# (pe1) o it/ot2 daa: voice# 80 a8 o it/ot8 eb: a8 17 reserved (pe2) o it /ot2 reserved 81 a9 o it/ot8 eb: a9 18 nvmdata (pe3) i/o it/ot2 nvram: sda 82 pllvdd p pwr +3.3v and to gnd through 0.1 f 19 hs_lcs (pe4) i it/ot2 gnd through 47 k ? 83 pllgnd g gnd gnd 20 vdd_core p pwr internal core voltage 84 a10 o it/ot8 eb: a10 21 celdata (pe5) i/o it/ot2 +3.3v through 47 k ? 85 vdd_core p pwr internal core voltage 22 ssd_ring# (pe6) o it/ot2 nc 86 a11 o it/ot8 eb: a11 23 line_sel (pe7) i it/ot8 +3.3v through 47 k ? 87 a12 o it/ot8 eb: a12 24 reserved (pa0) o it/ot2 nc 88 a13 o it/ot8 eb: a13 25 gnd g gnd gnd 89 a14 o it/ot8 eb: a14 26 ssd_int (pa1) o it/ot2 nc 90 gnd g gnd gnd 27 pa2 i/o it/ot2 nc 91 a15 o it/ot8 eb: a15 28 reserved (pa3) i itpu/ot2 reserved 92 sr2clk (p_pgp05 ) i itpu/ot2 vc: m_sck 29 reserved (pa4) i itpu/ot2 reserved 93 dib_datap i/o i dd/odd dib: data pos. channel 30 gnd g gnd gnd 94 dib_datan i/o idd/odd dib: data neg. channel 31 reserved (pa5) i it/ot2 +3.3v through 47 k ? 95 gnd g gnd gnd 32 pa6 i/o it/ot2 nc 96 pwrclkp o odpc dib: transformer primary winding non- dotted terminal 33 nvmclk (pa7) o it/ot2 nvram: scl 97 pwrclkn o odpc dib: transformer primary winding dotted terminal 34 reset# i it hb: reset# 98 dspkout o it/ot2 speaker circuit 35 sr3out o ot2 vc: m_txsin 99 a16 (pb0) o it/ot2 eb: a16 36 sr3in (p_px01) i itk/ot2 vc: m_rxout 100 vdd p pwr +3.3v 37 m_clk (p_pb00) o it/ot2 vc: m_ clkin 101 reserved (pb1) o it/ot2 nc 38 sa2clk (p_px05) i itpu/ot2 vc: m_strobe 102 romsel# (pb2) o ot2 eb: rom ce# 39 sr2io (p_px06) o it/ot2 vc: m_cntrlsin 103 gnd g gnd gnd 40 vdd p pwr +3.3v 104 ramsel# (pb3) o it/ot2 eb: ram cs# 41 p_px00 i/o it/ot8 nc 105 a17 (pb4) o it/ot2 eb: a17 42 p_px02 i/o itpu/ot2 nc 106 a18 (pb5) o it/ot2 eb: a18 43 p_px03 i/o itpu/ot2 nc 107 ext_res# (pb6) o it/ot2 nc 44 gnd g gnd gnd 108 vdd p pwr +3.3v 45 sr4in i itk nc 109 hint ( pb7) o it/ot8 hb: hint 46 pd7 i/o it/ot2 nc 110 testp i itpu nc
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-7 table 3-1. cx81801 modem 128-pin tqfp pin signals for parallel interface (parif = high) (continued) pin signal label i/o i/o type interface pin signal label i/o i/o type interface 47 noxyck i itpu gnd 111 dv1tp i itpu clock select 48 gnd g gnd gnd 112 gnd g gnd gnd 49 xclk o it/ot2 nc 113 clkin i it gnd 50 iasleep (p_pf05) o ot2 vc: sleep 114 xtli i ix crystal circuit 51 reserved (p_pb01) i/o itpu/ot2 nc 115 xtlo o ox crystal circuit 52 reserved (gp00) i/o it/ot2 nc 116 vdd p pwr +3.3v 53 vdd_core p pwr internal core voltage 117 nmi# i ithpu +3.3v 54 reserved (p_pa04) i/o itpu/ot2 nc 118 write# o it/ot2 eb: write# 55 reserved (p_pa00) i/o itpu/ot2 nc 119 read# o it/ot2 eb: read# 56 reserved (p_pa05) i/o itk/ot2 nc 120 gnd g gnd gnd 57 lpo i itpu/ot2 +3.3v through 240 k ? 121 phs2 o ot2 nc 58 vdd p pwr +3.3v 122 hd0 (pc0) i/o ith/ot8 hb: hd0 59 reserved (bd2clk) o itpu/ot2 nc 123 hd1 (pc1) i/o ith/ot8 hb: hd1 60 vgg p pwrg +3.3v or +5v 124 vdd p pwr +3.3v 61 clkout o it/ot2 nc 125 hd2 (pc2) i/o ith/ot8 hb: hd2 62 d0 i/o ith/ot2 eb: d0 126 hd3 (pc3) i/o ith/ot8 hb: hd3 63 d1 i/o ithot2 eb: d1 127 hd4 (pc4) i/o ith/ot8 hb: hd4 64 d2 i/o ith/ot2 eb: d2 128 gnd g gnd gnd notes: 1. i/o types: see table 3-5. 2. interface legend: dib digital isolation barrier eb expansion bus hb host bus nc no internal pin connection vc voice codec
cx81801-7x/8x smartv.xx modem data sheet 3-8 conexant 102199b table 3-2. cx81801 modem pin signal defini tions for parallel interface (parif = high) label pin i/o i/o type signal name/description system xtli, xtlo 114, 115 i, o ix, ox crystal in and crystal out. if an external 28.224 mhz crystal circuit is used instead of an exte rnal clock circuit, connect xtli and xtlo to the external crystal circuit and connect clkin to digital ground (gnd). clkin 113 i it clock in. if an external 28.224 mhz clock circuit is used instead of an external crystal circuit, connect clkin to the clock output and leave xtli and xtlo open. clkout 61 o it/ot2 clock out. 28.224 mhz output clock. leave open. dv1tp 111 i itpu clock input select. this input is used to choose the clock input. connect to +3.3v or leave open to select xtli as the clock input. connect to gnd to select clkin as the clock input. parif 5 i itpu parallel/serial interface select. parif input high (open) selects parallel host interface operation (see this table); parif low (gnd) selects serial dte interface operation (see table 3-4). line_sel (pe7) 23 i it/ot8 line interface select. selects telephone line interface. connect to +3.3v though 47 k ? . stpmode# (pd3) 9 i ith/ot2 stop mode. not used. leave open. nmi# 117 i ithpu non-maskable interrupt. not used. connect to +3.3v. reset# 34 i it reset. the active low reset# input resets the smart modem logic, and restores the saved conf iguration from serial eeprom or returns the modem to the factory default values if nvram is not present. reset# low holds the modem in the reset state; reset# going high releases the modem from the reset state. after application of vdd, reset# must be held low for at least 15 ms after the vdd power reaches operating range. t he modem device set is ready to use 25 ms after the low-to-high transition of reset#. for parallel interface, connect reset# input to the host bus reset line through an inverter. vgg 60 p pwrg i/o signaling voltage source. connect to +3.3v for +3.3v inputs, or to +5v for +5v inputs. vdd 2, 15, 40, 58, 78, 100, 108, 116, 124 p pwr digital supply voltage. connect to vcc (+3.3v, filtered). vdd_core 20, 53, 85 p pwr core voltage. internal core voltage. gnd 10, 25, 30, 44, 48, 68, 90, 95, 103, 112, 120, 128 g gnd digital ground. connect to digital ground (gnd). lpo 57 i i/o low power oscillator. connect to +3.3v through 240 k ? . noxyck 47 i itpu disable xclk output . when low, disables xclk output (reduces internal power consumption). when high, enables xclk output. connect to gnd. pllvdd 82 p pwr pll circuit digital supply voltage. connect to +3.3v and to gnd through 0.1 f. pllgnd 83 g gnd pll circuit digital ground. connect to gnd. serial eeprom (nvram) interface nvmclk (pa7) 33 o it/ot2 nvram clock. nvmclk output high enables the eeprom. connect to eeprom scl pin. nvmdata (pe3) 18 i/o it/ot2 nvram data. the nvmdata pin supplies a serial data interface to the eeprom. connect to eeprom sda pin and to +3.3v through 10 k ? .
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-9 table 3-2. cx81801 modem pin signal definitions for parallel interface (pari f = high) (continued) label pin i/o i/o type signal name/description speaker interface dspkout 98 o it/ot2 modem speaker digital output. the dspkout digital output reflects the received analog input si gnal digitized to ttl high or low level by an internal comparator. dib interface pwrclkp 96 o odpc clock and power positive. provides clock and power to the lsd. connect to dib transformer primary winding non-dotted terminal. pwrclkn 97 o odpc clock and power negative. provides clock and power to the lsd. connect to dib transformer primary winding dotted terminal. dib_datap 93 i/o idd/odd data positive. transfers data, control, and status information between the smart modem and the lsd. connect to lsd through dib data positive channel components. dib_datan 94 i/0 idd/odd data negative. transfers data, control, and status information between the smart modem and the lsd. connect to lsd through dib data negative channel components. external bus interface a0-a9, a10-a15, a16 (pb0), a17 (pb4), a18 (pb5) 71-77, 79-81, 84, 86-89, 91, 99, 105, 106 o, o, o, o, o it/ot8, it/ot8, it/ot2, it/ot2, it/ot2 address lines 0-18. a0-a18 are the address output lines used to access external memory; up to 4 mb (512 kb) rom/flash rom using a0-a18 and up to 1 mb (128 kb) ram using a0-a16. the 256 kb base modem rom code is located in the 0-256 kb address range. d0-d7 62-67, 69-70 i/o ith/ot2 data line 0-7. d0-d7 are the bidirectional external memory bus data lines. read# 119 o it/ot2 read enable. read# output low enables data transfer from the selected device to the d0-d7 lines. write# 118 o it/ot2 write enable. write# output low enables data transfer from the d0-d7 lines to the selected device. romsel# (pb2) 102 o ot2 rom select . romsel# (pb2, es3) output low selects the external rom/flash rom. ramsel# (pb3) 104 o it/ot2 ram select. ramsel# (pb3, es2) output low selects the external ram. reserved (pb1) 101 o it/ot2 reserved. pb1 (es4) is used internally. leave open. ext_res# (pb6) 107 o it/ot2 external device reset. active low reset for external devices. leave open if not used. cx20442 vc interface iasleep (p_pf05) 50 o ot2 modem sleep. connect to vc sleep pin. m_clk (p_pb00) 37 o it/ot2 master clock output . connect to vc m_clkin pin. sr2clk (p_pgp05) 92 i itpu/ot2 voice serial clock input. connect to vc m_sck pin. sa2clk (p_px05) 38 i itpu/ot2 voice serial frame sync input. connect to vc m_strobe pin. sr3out 35 o ot2 voice serial transmit data output. connect to vc m_txsin pin. sr3in (p_px01) 36 i itk/ot2 voice serial receive data input. connect to vc m_rxout pin. sr2io (p_px06) 39 o it/ot2 voice control output. connect to vc m_cntrlsin pin.
cx81801-7x/8x smartv.xx modem data sheet 3-10 conexant 102199b table 3-2. cx81801 modem pin signal definitions for parallel interface (pari f = high) (continued) label pin i/o i/o type signal name/description parallel host interface hcs# (pd4) 11 i it host bus chip select. hcs# input low enables the mcu host bus interface. hwt# (pd5) 12 i ithpu host bus write. hwt# is an active low, write control input. when hcs# is low, hwt# low allows the host to write data or control words into a selected mcu register. hrd# (pd6) 13 i ithpu host bus read. hrd# is an active low, read control input. when hcs# is low, hrd# low allows the host to read status information or data from a selected mcu register. hint (pb7) 109 o it/ot8 host bus interrupt. hint output is set high when the receiver error flag, received data availabl e, transmitter holding register empty, or modem status interrupt is asserted. hint is reset low upon the appropriate interrupt service or master reset operation. ha0-ha2 (pd0-pd2) 6-8 i ithpd/ot2 host bus address lines 0-2. during a host read or write operation with hcs# low, ha0-ha2 select an internal mcu 16550a-compatible register. hd0-hd7 (pc0-pc7) 122-123, 125- 127, 1, 3-4 i/o ith/ot8 host bus data lines 0-7 . hd0-hd7 are three-state input/output lines providing bidirectional communication between the host and the mcu. data, control words, and status information are transferred over hd0-hd7.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-11 table 3-2. cx81801 modem pin signal definitions for parallel interface (pari f = high) (continued) label pin i/o i/o type signal name/description daa interface voice# (pe1) 16 o it/ot2 voice relay control. this output (typically active low) used to control the normally open voice relay. hs_lcs (pe4) 19 i it/ot2 handset line current sense. lcs is an active high input that indicates a handset off-hook status. not required for data/fax/voice/speakerphone operation. if not used, connect to gnd through 47 k ? . not used testp 110 i itpu test. used for factory test only. leave open. xclk 49 o it/ot2 not used. leave open. phs2 121 o ot2 not used. leave open. sr4rin 45 i itk not used. leave open. pa2 27 i it/ot2 not used. leave open. pa6 32 o it/ot2 not used. leave open. pd7 46 i/o it/ot2 not used. leave open. p_px00 41 i/o it/ot8 not used. leave open. p_px02 42 i/o itpu/ot2 not used. leave open. p_px03 43 i/o itpu/ot2 not used. leave open. reserved (pa0) 24 o it/ot2 not used. leave open. reserved (pa1) 26 o it/ot2 not used. leave open. reserved (pa3) 28 i itpu/ot2 not used. leave open. reserved (pa4) 29 i itpu/ot2 not used. leave open. reserved (pa5) 31 i it/ot2 reserved. connect to +3.3v though 47 k ? . reserved (pe0) 14 o it/ot8 not used. leave open. reserved (pe2) 17 o it/ot2 not used. leave open. reserved (pe5) 21 i/o it/ot2 reserved. connect to +3.3v though 47 k ? . reserved (pe6) 22 o it/ot2 not used. leave open. reserved (gp00) 52 i/o it/ot2 not used. leave open. reserved (p_pa00) 55 i/o itpu/ot2 not used. leave open. reserved (p_pa04) 54 i/o itpu/ot2 not used. leave open. reserved (p_pa05) 56 i/o itk/ot2 not used. leave open. reserved (p_pb01) 51 i/o itpu/ot2 not used. leave open. reserved (p_bd2clk) 59 i/o itpu/ot2 not used. leave open. notes: 1. i/o types: see table 3-5. 2. interface legend: dib digital isolation barrier eb expansion bus hb host bus nc no internal pin connection vc voice codec reserved = no external connection a llowed (may have internal connection).
cx81801-7x/8x smartv.xx modem data sheet 3-12 conexant 102199b figure 3-3. cx81801 modem hardware signals for serial interface (parif = low) xtli xtlo clkin clkout xclk dv1tp lpo noxyck parif stpmode# (pd3) nmi# reset# aaind# (pc4) tmind# (pb7) dtrind# (pd0) ohind# (pe0) txd# (pa2) rxd# (pa6) cts# (pc1) dsr# (pc0) rlsd# (pc2) tm# (pc6) ri# (pc5) dtr# (pd4) rts# (pd6) rxclk# (p_pb01) txclk# (p_pa05) xtclk # (p_gp00) reserved (pa0) reserved (pe6) reserved (pa1) testp phs2 sr4in pc3 pd1 pd2 pd7 reserved (pb1) reserved (pc7) reserved (pd5) reserved (p_pa00) reserved (p_pa05) reserved (bd2clk) p_px00 p_px02 p_px03 vgg vdd vdd vdd vdd vdd vdd vdd vdd vdd vdd_core vdd_core vdd_core gnd gnd gnd gnd gnd gnd gnd gnd gnd gnd gnd gnd 114 115 113 61 49 111 57 47 5 9 117 34 127 109 6 14 27 32 123 122 125 3 1 11 13 51 54 52 24 22 26 110 121 45 126 7 8 46 101 4 12 55 56 59 41 42 43 60 2 15 40 58 78 100 108 116 124 20 53 85 10 25 30 44 48 68 90 95 103 112 120 128 serial dte interface line_sel (pe7) reserved (pa5) reserved (pa4) reserved (pe5) reserved (pe2) reserved (pa3) voice# (pe1) hs_lcs (pe4) dspkout pwrclkp pwrclkn dib_datap dib_datan iasleep (p_pf05) m_clk (p_pb00) sr2clk (p_pgp05) sa2clk (p_px05) sr3out sr3in (p_px01) sr2io (p_px06) nvmclk (pa7) nvmdata (pe3) a0 a1 a2 a3 a4 a5 a6 a7 a8 a9 a10 a11 a12 a13 a14 a15 a16 (pb0) a17 (pb4) a18 (pb5) d0 d1 d2 d3 d4 d5 d6 d7 write# read# romsel# (pb2) ramsel# (pb3) ext_res# (pb6) pllvdd pllgnd 23 31 29 21 17 28 16 19 98 96 97 93 94 50 37 92 38 35 36 39 33 18 71 72 73 74 75 76 77 79 80 81 84 86 87 88 89 91 99 105 106 62 63 64 65 66 67 69 70 118 119 102 104 107 82 83 eeprom (optional) 102199_005 +3.3v cx81801 smart modem 128-pin tqfp serial interface (parif = low) +3.3v digital isolation barrier (dib) 0.1 uf nc crystal circuit nc external memory led interface reset circuit speaker circuit sleep m_clkin m_sck m_strobe m_txsin m_rxout m_cntrlsin nc +3.3v +3.3v or +5v voice# hs_lcs cx20442 voice codec (vc) (optional) serial dte synchronous clocks nc nc nc +3.3v 240k nc +3.3v daa 47k +3.3v 47k +3.3v 47k nc nc
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-13 figure 3-4. cx81801 modem 128-pin tqfp pin signals for serial interface (parif = low) 102199_006 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 4 0 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 5 0 5 1 5 2 5 3 5 4 5 5 5 6 5 7 5 8 5 9 6 0 6 1 6 2 6 3 6 4 1 0 2 1 0 1 1 0 0 9 9 9 8 9 7 9 6 9 5 9 4 9 3 9 2 9 1 9 0 8 9 8 8 8 7 8 6 8 5 8 4 8 3 8 2 8 1 8 0 7 9 7 8 7 7 7 6 7 5 7 4 7 3 7 2 7 1 7 0 6 9 6 8 6 7 6 6 6 5 1 2 8 1 2 7 1 2 6 1 2 5 1 2 4 1 2 3 1 2 2 1 2 1 1 2 0 1 1 9 1 1 8 1 1 7 1 1 6 1 1 5 1 1 4 1 1 3 1 1 2 1 1 1 1 1 0 1 0 9 1 0 8 1 0 7 1 0 6 1 0 5 1 0 4 1 0 3 g n d a a i n d # ( p c 4 ) p c 3 r l s d # ( p c 2 ) v d d c t s # ( p c 1 ) d s r # ( p c 0 ) p h s 2 g n d r e a d # w r i t e # n m i # v d d x t l o x t l i c l k i n g n d d v 1 t p t e s t p t m i n d # ( p b 7 ) v d d e x t _ r e s # ( p b 6 ) a 1 8 ( p b 5 ) a 1 7 ( p b 4 ) r a m s e l # ( p b 3 ) g n d s r 2 i o ( p _ p x 0 6 ) v d d p _ p x 0 0 p _ p x 0 2 p _ p x 0 3 g n d s r 4 i n p d 7 n o x y c k g n d x c l k i a s l e e p ( p _ p f 0 5 ) r x c l k # ( p _ p b 0 1 ) x t c l k # ( g p 0 0 ) v d d _ c o r e t x c l k # ( p _ p a 0 4 ) r e s e r v e d ( p _ p a 0 0 ) r e s e r v e d ( p _ p a 0 5 ) l p o v d d r e s e r v e d ( b d 2 c l k ) v g g c l k o u t d 0 d 1 d 2 r o m s e l # ( p b 2 ) r e s e r v e d ( p b 1 ) v d d a 1 6 ( p b 0 ) d s p k o u t p w r c l k n p w r c l k p g n d d i b _ d a t a n d i b _ d a t a p s r 2 c l k ( p _ p g p 0 5 ) a 1 5 g n d a 1 4 a 1 3 a 1 2 a 1 1 v d d _ c o r e a 1 0 p l l g n d p l l v d d a 9 a 8 a 7 v d d a 6 a 5 a 4 a 3 a 2 a 1 a 0 d 7 d 6 g n d d 5 d 4 d 3 r i # ( p c 5 ) v d d t m # ( p c 6 ) r e s e r v e d ( p c 7 ) p a r i f d t r i n d # ( p d 0 ) p d 1 p d 2 s t p m o d e # ( p d 3 ) g n d d t r # ( p d 4 ) r e s e r v e d ( p d 5 ) r t s # ( p d 6 ) o h i n d # ( p e 0 ) v d d v o i c e # ( p e 1 ) r e s e r v e d ( p e 2 ) n v m d a t a ( p e 3 ) h s _ l c s ( p e 4 ) v d d _ c o r e r e s e r v e d ( p e 5 ) r e s e r v e d ( p e 6 ) l i n e _ s e l ( p e 7 ) r e s e r v e d ( p a 0 ) g n d r e s e r v e d ( p a 1 ) t x d # ( p a 2 ) r e s e r v e d ( p a 3 ) r e s e r v e d ( p a 4 ) g n d r e s e r v e d ( p a 5 ) r x d # ( p a 6 ) n v m c l k ( p a 7 ) r e s e t # s r 3 o u t s r 3 i n ( p _ p x 0 1 ) m _ c l k ( p _ p b 0 0 ) s a 2 c l k ( p _ p x 0 5 ) cx81801 serial interface (parif pin = low)
cx81801-7x/8x smartv.xx modem data sheet 3-14 conexant 102199b table 3-3. cx81801 modem 128-pin tqfp pin signals for serial interface (parif = low) pin signal label i/o i/o type interface pin signal label i/o i/o type interface 1 ri# (pc5) o ith/ot8 dte if: ri# 65 d3 i/o ith/ot2 eb: d3 2 vdd p pwr +3.3v 66 d4 i/o ith/ot2 eb: d4 3 tm# (pc6) o ith/ot8 dte if: tm# 67 d5 i/o ith/ot2 eb: d5 4 reserved (pc7) i ith/ot8 +3.3v through 47 k ? 68 gnd g gnd gnd 5 parif i itpu gnd (serial interface) 69 d6 i/o ith/ot2 eb: d6 6 dtrind# (pd0) o ithpd/ot2 led: dtrind# 70 d7 i/o ith/ot2 eb: d7 7 pd1 i/o ithpd/ot2 nc 71 a0 o it/ot8 eb: a0 8 pd2 i/o ithpd/ot2 nc 72 a1 o it/ot8 eb: a1 9 stpmode# (pd3) i ith/ot2 nc 73 a2 o it/ot8 eb: a2 10 gnd g gnd gnd 74 a3 o it/ot8 eb: a3 11 dtr# (pd4) i it dte if: dtr# 75 a4 o it/ot8 eb: a4 12 reserved (pd5) i ithpu nc 76 a5 o it/ot8 eb: a5 13 rts# (pd6) i ithpu dte if: rts# 77 a6 o it/ot8 eb: a6 14 ohind# (pe0) o it/ot8 led: ohind# 78 vdd p pwr +3.3v 15 vdd p pwr +3.3v 79 a7 o it/ot8 eb: a7 16 voice# (pe1) o it/ot2 daa: voice# 80 a8 o it/ot8 eb: a8 17 reserved (pe2) o it/ot2 nc 81 a9 o it/ot8 eb: a9 18 nvmdata (pe3) i/o it/ot2 nvram: sda 82 pllvdd p pwr +3.3v and gnd through 0.1 f 19 hs_lcs (pe4) i it/ot2 gnd through 47 k ? 83 pllgnd g gnd gnd 20 vdd_core p pwr internal core voltage 84 a10 o it/ot8 eb: a10 21 reserved (pe5) i/o it/ot2 +3.3v through 47 k ? 85 vdd_core p pwr internal core voltage 22 ssd_ring# (pe6) o it/ot2 nc 86 a11 o it/ot8 eb: a11 23 line_sel (pe7) i it/ot8 +3.3v through 47 k ? 87 a12 o it/ot8 eb: a12 24 reserved (pa0) o it/ot2 nc 88 a13 o it/ot8 eb: a13 25 gnd g gnd gnd 89 a14 o it/ot8 eb: a14 26 ssd_int (pa1) o it/ot2 nc 90 gnd g gnd gnd 27 txd# (pa2) i it/ot2 dte if: txd# 91 a15 o it/ot8 eb: a15 28 reserved (pa3) i itpu/ot2 nc 92 sr2clk (p_pgp05) i itpu/ot2 vc: m_sck 29 reserved (pa4) i itpu/ot2 nc 93 dib_da tap i/o idd/odd dib: data pos. channel 30 gnd g gnd gnd 94 dib_datan i/o idd/odd dib: data neg. channel 31 reserved (pa5) i it/ot2 +3.3v through 47 k ? 95 gnd g gnd gnd 32 rxd# (pa6) o it/ot2 dte if: rxd# 96 pwrclkp o odpc dib: transformer primary winding non- dotted terminal 33 nvmclk (pa7) o it/ot2 nvram: scl 97 pwrclkn o odpc dib: transformer primary winding dotted terminal 34 reset# i it reset circuit 98 dspko ut o it/ot2 speaker circuit 35 sr3out o ot2 vc: m_txsin 99 a16 (pb0) o it/ot2 eb: a16 36 sr3in (p_px01) i itk/ot2 vc: m_rxout 100 vdd p pwr +3.3v 37 m_clk (p_pb00) o it/ot2 vc: m_ clkin 101 reserved (pb1) o it/ot2 nc 38 sa2clk (p_px05) i itpu/ot2 vc: m_strobe 102 romsel# (pb2) o ot2 eb: rom ce# 39 sr2io (p_px06) o it/ot2 vc: m_cntrlsin 103 gnd g gnd gnd 40 vdd p pwr +3.3v 104 ramsel# (pb3) o it/ot2 eb: ram cs# 41 p_px00 i/o it/ot8 nc 105 a17 (pb4) o it/ot2 eb: a17 42 p_px02 i/o itpu/ot2 nc 106 a18 (pb5) o it/ot2 eb: a18 43 p_px03 i/o itpu/ot2 nc 107 ext_res# (pb6) o it/ot2 nc 44 gnd g gnd gnd 108 vdd p pwr +3.3v 45 sr4in i itk nc 109 tmind# ( pb7) o it/ot8 led: tmind# 46 pd7 i/o it/ot2 nc 110 testp i itpu nc
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-15 table 3-3. cx81801 modem 128-pin tqfp pin signals for serial interface (parif = low) (continued) pin signal label i/o i/o type interface pin signal label i/o i/o type interface 47 noxyck i itpu gnd 111 dv1tp i itpu clock select 48 gnd g gnd gnd 112 gnd g gnd gnd 49 xclk o it/ot2 nc 113 clkin i it gnd 50 iasleep (p_pf05) o ot2 vc: sleep 114 xtli i ix crystal circuit 51 rxclk# (p_pb01) o itpu/ot2 dte: rxclk 115 xtlo o ox crystal circuit 52 xtclk# (gp00) i it/ot2 dte: xtclk 116 vdd p pwr +3.3v 53 vdd_core p pwr internal core voltage 117 nmi# i ithpu +3.3v 54 txclk# (p_pa04) o itpu/ot2 dte: tx clk 118 write# o it/ot2 eb: write# 55 reserved (p_pa00) i/o itpu/ot2 nc 119 read# o it/ot2 eb: read# 56 reserved (p_pa05) i/o itk/ot2 nc 120 gnd g gnd gnd 57 lpo i itpu/ot2 +3.3v through 240 k ? 121 phs2 o ot2 nc 58 vdd p pwr +3.3v 122 dsr# (pc0) i/o ith/ot8 dte if: dsr# 59 reserved (bd2clk) o itpu/ot2 nc 123 cts# (pc1) i/o ith/ot8 dte if: cts# 60 vgg p pwrg +3.3v or +5v 124 vdd p pwr +3.3v 61 clkout o it/ot2 nc 125 rlsd# (p c2) i/o ith/ot8 dte if: rlsd# 62 d0 i/o ith/ot2 eb: d0 126 pc3 i/o ith/ot8 nc 63 d1 i/o ithot2 eb: d1 127 aaind# (pc4) o ith/ot8 led: aaind# 64 d2 i/o ith/ot2 eb: d2 128 gnd g gnd gnd notes: 1. i/o types: see table 3-5. 2. interface legend: dib digital isolation barrier eb expansion bus hb host bus nc no internal pin connection vc voice codec
cx81801-7x/8x smartv.xx modem data sheet 3-16 conexant 102199b table 3-4. cx81801 modem pin signal definitions for serial interface (parif = low) label pin i/o i/o type signal name/description system xtli, xtlo 114, 115 i, o ix, ox crystal in and crystal out. if an external 28.224 mhz crystal circuit is used instead of an exte rnal clock circuit, connect xtli and xtlo to the external crystal circuit and connect clkin to digital ground (gnd). clkin 113 i it clock in. if an external 28.224 mhz clock circuit is used instead of an external crystal circuit, connect clkin to the clock output and leave xtli and xtlo open. clkout 61 o it/ot2 clock out. 28.224 mhz output clock. leave open. dv1tp 111 i itpu clock input select. this input is used to choose the clock input. connect to +3.3v or leave open to select xtli as the clock input. connect to gnd to select clkin as the clock input. parif 5 i itpu parallel/serial interface select. parif input high (open) selects parallel host interface operation (see signal definitions in table 3-2); parif low (gnd) selects serial dte interface operation (see signal definitions in this table). line_sel (pe7) 23 i it/ot8 line interface select. selects telephone line interface. connect to +3.3v. stpmode# (pd3) 9 i ith/ot2 stop mode. not used. leave open. nmi# 117 i ithpu non-maskable interrupt. not used. connect to +3.3v. reset# 34 i it reset. the active low reset# input resets the smart modem logic, and restores the saved conf iguration from serial eeprom or returns the modem to the factory default values if nvram is not present. reset# low holds the modem in the reset state; reset# going high releases the modem from the reset state. after application of vdd, reset# must be held low for at least 15 ms after the vdd power reaches operating range. t he modem device set is ready to use 25 ms after the low-to-high transition of reset#. for serial interface, the reset# input is typically connected to a reset switch circuit. vgg 60 p pwrg i/o signaling voltage source. connect to +3.3v for +3.3v inputs, or to +5v for +5v inputs. vdd 2, 15, 40, 58, 78, 100, 108, 116, 124 p pwr digital supply voltage. connect to vcc (+3.3v, filtered). vdd_core 20, 53, 85 p pwr core voltage. internal core voltage. gnd 10, 25, 30, 44, 48, 68, 90, 95, 103, 112, 120, 128 g gnd digital ground. connect to digital ground (gnd). lpo 57 i i/o low power oscillator. connect to +3.3v through 240 k ? . noxyck 47 i itpu disable xclk output . when low, disables xclk output (reduces internal power consumption). when high, enables xclk output. connect to gnd. pllvdd 82 p pwr pll circuit digital supply voltage. connect to +3.3v and to gnd through 0.1 f. pllgnd 83 g gnd pll circuit digital ground. connect to gnd. serial eeprom (nvram) interface nvmclk (pa7) 33 o it/ot2 nvram clock. nvmclk output high enables the eeprom. connect to eeprom scl pin. nvmdata (pe3) 18 i/o it/ot2 nvram data. the nvmdata pin supplies a serial data interface to the eeprom. connect to eeprom sda pin and to +3.3v through 10 k ? .
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-17 table 3-4. cx81801 modem pin signal definitions for serial interface (parif = low) (continued) label pin i/o i/o type signal name/description speaker interface dspkout 98 o it/ot2 modem speaker digital output. the dspkout digital output reflects the received analog input signal digitized to ttl high or low level by an internal comparator. dib interface pwrclkp 96 o odpc clock and power positive. provides clock and power to the lsd. connect to dib transformer primary winding non-dotted terminal. pwrclkn 97 o odpc clock and power negative. provides clock and power to the lsd. connect to dib transformer primary winding dotted terminal. dib_datap 93 i/o idd/odd data positive. transfers data, control, and status information between the smart modem and the lsd. connect to lsd through dib data positive channel components. dib_datan 94 i/0 idd/odd data negative. transfers data, control, and status information between the smart modem and the lsd. connect to lsd through dib data negative channel components. external bus interface a0-a9, a10-a15, a16 (pb0), a17 (pb4), a18 (pb5) 71-77, 79-81, 84, 86-89, 91, 99, 105, 106 o, o, o, o, o it/ot8, it/ot8, it/ot2, it/ot2, it/ot2 address lines 0-18. a0-a18 are the address output lines used to access external memory; up to 4 mb (512 kb) rom/flash rom using a0-a18 and up to 1 mb (128 kb) ram using a0-a16. the 256 kb base modem rom code is located in the 0-256 kb address range. d0-d7 62-67, 69-70 i/o ith/ot2 data line 0-7. d0-d7 are bidirectional external memory bus data lines. read# 119 o it/ot2 read enable. read# output low enables data transfer from the selected device to the d0-d7 lines. write# 118 o it/ot2 write enable. write# output low enables data transfer from the d0-d7 lines to the selected device. romsel# (pb2) 102 o ot2 rom select . romsel# (pb2, es3) output low selects the external rom. ramsel# (pb3) 104 o it/ot2 ram select. ramsel# (pb3, es2) output low selects the external ram. reserved (pb1) 101 o it/ot2 reserved. pb1 (es4) is used internally. leave open. ext_res# (pb6) 107 o it/ot2 external device reset. active low reset for external devices. leave open if not used. cx20442 vc interface iasleep (p_pf05) 50 o ot2 modem sleep. connect to vc sleep pin. m_clk (p_pb00) 37 o it/ot2 master clock output . connect to vc m_clkin pin. sr2clk (p_pgp05) 92 i itpu/ot2 voice serial clock input. connect to vc m_sck pin. sa2clk (p_px05) 38 i itpu/ot2 voice serial frame sync input. connect to vc m_strobe pin. sr3out 35 o ot2 voice serial transmit data output. connect to vc m_txsin pin. sr3in (p_px01) 36 i itk/ot2 voice serial receive data input. connect to vc m_rxout pin. sr2io (p_px06) 39 o it/ot2 voice control output. connect to vc m_cntrlsin pin.
cx81801-7x/8x smartv.xx modem data sheet 3-18 conexant 102199b table 3-4. cx81801 modem pin signal definitions for serial interface (parif = low) (continued) label pin i/o i/o type signal name/description v.24 (eia/tia-232-e) dte serial interface txd# (pa2) 27 i it/ot2 transmitted data (eia ba/itu-t ct103). the dte uses the txd# line to send data to the modem for transmission over the telephone line or to transmit commands to the modem. rxd# (pa6) 32 o it/ot2 received data (eia bb/itu-t ct104). the modem uses the rxd# line to send data received from the telephone line to the dte and to send modem responses to the dte. during command mode, rxd# data represents the modem responses to the dte. cts# (pc1) 123 o ith/ot8 clear to send (eia cb/itu-t ct106). cts# output on (low) indicates that the modem is ready to accept data from the dte. in asynchronous operation, in error correction or normal mode, cts# is always on (low) unless rts/cts flow control is selected by the &kn command. in synchronous operation, the mo dem also holds cts# on during asynchronous command state. the modem turns cts# off immediately upon going off-hook and holds cts# off until both dsr# and rlsd# are on and the modem is ready to transmit and receive synchronous data. the modem can also be commanded by the &rn command to turn cts# on in response to an rts# off-to-on transition. dsr# (pc0) 122 o ith/ot8 data set ready (eia cc/itu-t ct107). dsr# indicates modem status to the dte. dsr# off (high) indicates that the dte is to disregard all signals appearing on t he interchange circuits except ring indicator (ri#). dsr# output is controlled by the at&sn command. rlsd# (pc2) 125 o ith/ot8 received line signal detector (eia cf/itu-t ct109). when at&c0 command is not in effect, rlsd# output is on when a carrier is detected on the telephone line or off when carrier is not detected. tm# (pc6) 3 o ith/ot8 test mode (eia tm/itu-t ct142). the tm# output indicates the modem is in test mode (low) or in any other mode (high). ri# (pc5) 1 o ith/ot8 ring indicator (eia ce/itu-t ct125). ri# output on (low) indicates the presence of an on segment of a ring signal on the telephone line. dtr# (pd4) 11 i it data terminal ready (eia cd/itu-t ct108). the dtr# input is turned on (low) by the dte when the dte is ready to transmit or receive data. dtr# on prepares the modem to be connected to the telephone line, and maintains the connection established by the dte (manual answering) or internally (automatic answering). dtr# off places the modem in the disconnect state under control of the &dn and &qn commands. rts# (pd6) 13 i ithpu request to send (eia ca/itu-t ct105). rts# input on (low) indicates that the dte is ready to send data to the modem. in the command state, the modem ignores rts#. in asynchronous operation, the modem ignores rts# unless rts/cts flow control is selected by the &kn command. in synchronous on-line operation, the modem can be commanded by the &rn command to ignore rts# or to respond to rts# by turning on cts# after the delay specified by register s26.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-19 table 3-4. cx81801 modem pin signal definitions for serial interface (parif = low) (continued) label pin i/o i/o type signal name/description v.24 (eia/tia-232-e) dte serial interface (continued) rxclk# (p_pb01) 51 o itpu/ot2 receive data clock. a synchronous receive data clock (rxclk) is output in synchronous modes. the rxclk frequency is the data rate (0.01%) with a duty cycle of 501%. leave open if not used. txclk# (p_pa04) 54 o itpu/ot2 transmit data clock. a synchronous transmit data clock (txclk) is output in synchronous modes. the txclk frequency is the data rate (0.01%) with a duty cycle of 501%. leave open if not used. xtclk# (gp00) 52 i it/ot2 external data clock. a synchronous external transmit data clock (xtclk) is input in synchronous modes. led indicator interface aaind# (pc4) 127 o ith/ot8 auto answer indicator. aaind# output on (low) corresponds to the indicator on. aaind# output is active when the modem is configured to answer the ring automatically (ats0 command 0). tmind# (pb7) 109 o it/ot8 test mode indicator. tmind# output on (low) corresponds to the indicator on. tmind# output pul ses (indicator flashes) when the modem is in test mode and if an error is detected. dtrind# (pd0) 6 o ithpd/ot2 dtr indicator. dtrind# output on (low) corresponds to the indicator on. the dtrind# state reflects the dtr# output state except when the &d0 command is active, in which case dtrind# is low. ohind# (pe0) 14 o it/ot8 off-hook indicator. ohind# (pe0) indicates the status of the off- hook relay.
cx81801-7x/8x smartv.xx modem data sheet 3-20 conexant 102199b table 3-4. cx81801 modem pin signal definitions for serial interface (parif = low) (continued) label pin i/o i/o type signal name/description daa interface voice# (pe1) 16 o it/ot2 voice relay control. this output (typically active low) used to control the normally open voice relay. hs_lcs (pe4) 19 i it/ot2 handset line current sense. lcs is an active high input that indicates a handset off-hook status. not required for data/fax/voice/speakerphone operation. if not used, connect to gnd through 47 k ? . not used testp 110 i itpu test. used for factory test only. leave open. xclk 49 o it/ot2 not used. leave open. s4rin 45 i itk not used. leave open. phs2 121 o ot2 not used. leave open. pc3 126 i/o ith/ot8 not used. leave open. pd1 7 i/o ithpd/ot2 not used. leave open. pd2 8 i/o ithpd/ot2 not used. leave open. pd7 46 i/o it/ot2 not used. leave open. p_px00 41 i/o it/ot8 not used. leave open. p_px02 42 i/o itpu/ot2 not used. leave open. p_px03 43 i/o itpu/ot2 not used. leave open. reserved (pa0) 24 o it/ot2 not used. leave open. reserved (pa1) 26 o it/ot2 not used. leave open. reserved (pa3) 28 i itpu/ot2 not used. leave open. reserved (pa4) 29 i itpu/ot2 not used. leave open. reserved (pa5) 31 i it/ot2 reserved. connect to +3.3v though 47 k ? . reserved (pc7) 4 i ith/ot8 reserved . connect to +3.3v through 47 k ? . reserved (pd5) 12 i ithpu reserved . leave open. reserved (pe2) 17 o it/ot2 not used. leave open. reserved (pe5) 21 i/o it/ot2 reserved. connect to +3.3v though 47 k ? . reserved (pe6) 22 o it/ot2 not used. leave open. reserved (p_pa00) 55 i/o itpu/ot2 not used. leave open. reserved (p_pa05) 56 i/o itk/ot2 not used. leave open. reserved (p_bd2clk) 59 i/o itpu/ot2 not used. leave open. notes: 1. i/o types: see table 3-5. 2. interface legend: dib digital isolation barrier eb expansion bus hb host bus nc no internal pin connection vc voice codec reserved = no external connection a llowed (may have internal connection).
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-21 table 3-5. cx81801 modem i/o type definitions i/o type description idd/odd digital input/output, dib data transceiver ix/ox i/o, wire it/ot2 digital input, +5v tolerant/ digital output, 2 ma, z int = 120 ? itk/ot2 digital input, +5v tolerant, keeper/ digital output, 2 ma, z int = 120 ? itpu/ot2 digital input, +5v tolerant, 75k ? pull up/ digital output, 2 ma, z int = 120 ? it/ot8 digital input, +5v tolerant,/ digital output, 8 ma, z int = 50 ? ithpd/ot2 digital input, +5v tolerant, hysteresis, 75k ? pull down/ digital output, 2 ma, z int = 120 ? ith/ot2 digital input, +5v tolerant, hysteresis/digital output, 2 ma, z int = 120 ? ith/ot8 digital input, +5v tolerant, hysteresis/digital output, 8 ma, z int = 50 ? it digital input, +5v tolerant itk digital input, +5v tolerant, keeper itkpu digital input, +5v tolerant, keeper, 75k ? pull up itpu digital input, +5v tolerant, 75k ? pull up ithpu digital input, +5v tolerant, hysteresis, 75k ? pull up odpc digital output with adjust able drive, dib clock and power ot2 digital output, three-state, 2 ma, z int = 120 ? pwr vcc power pwrg vgg power gnd ground notes: 1. see dc characteristics in table 3-6. 2. i/o type corresponds to the device pad type. the i/o column in signal interface tables refers to signal i/o direction used i n the application. table 3-6. cx81801 modem dc electrical characteristics parameter symbol min. typ. max. units test conditions input voltage low vil +5v tolerant 0 ? 0.8 v +5v tolerant hysteresis 0 ? 0.3 * vgg v input voltage high vih ? v +5v tolerant 2 ? 5.25 v +5v tolerant hysteresis 0.7 * vdd ? 5.25 v input hysteresis vh ? v +3v hysteresis 0.5 ? v +5v tolerant, hysteresis 0.3 ? v output voltage low vol z int = 120 ? 0 ? 0.4 v iol = 2 ma z int = 50 ? 0 ? 0.4 v iol = 8 ma output voltage high voh ? v z int = 120 ? 2.4 ? vdd v iol = -2 ma z int = 50 ? 2.4 ? vdd v iol = -8 ma pull-up resistance rpu 50 ? 200 k ? pull-down resistance rpd 50 ? 200 k ? test conditions unless otherwise stated: vdd = +3.3 0.3 vdc; ta = 0c to 70c; external load = 50 pf.
cx81801-7x/8x smartv.xx modem data sheet 3-22 conexant 102199b 3.2 cx20493 lsd hardware pins and signals 3.2.1 cx20493 lsd signal summary 3.2.1.1 smart modem interface (through dib) the dib interface, power, and ground signals are: ? clock (clk, pin 26); input ? digital power (pwr+, pin 7); unregulated input power ? regulated digital voltage supply (dvdd, pin 24) ? digital ground (dgnd, pin 23); digital ground ? regulated analog voltage supply (avdd, pin 2) ? analog ground (agnd, pin 6); analog ground ? data positive (dib_p, pin 27); input/output ? data negative (dib_n, pin 28); input/output 3.2.1.2 telephone line interface the telephone line interface signals are: ? ring 1 ac coupled (rac1, pin 21); input ? tip 1 ac coupled (tac1, pin 20); input ? ring 2 ac coupled (rac2, pin 19); input ? tip 2 ac coupled (tac2, pin 18); input ? tip and ring dc measurement (trdc, pin 12); input ? electronic inductor capacitor (eic, pin 11) ? electronic inductor output (eio, pin 17) ? electronic inductor feedback (eif, pin 16) ? receive analog input (rxi, pin 9); input ? transmit output (txo, pin 14); output ? transmit feedback (t xf, pin 13); input ? virtual impedance 0 (vz, pin 10); input ? electronic inductor ground (dc_gnd, pin 15) 3.2.1.3 voltage references there are three reference voltage pins: ? output middle (center) reference voltage (vc, pin 3); output for decoupling ? output reference voltage (vref, pin 4); output for decoupling ? bias resistor (rbias, pin 5); input
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-23 3.2.1.4 general purpose input/output there is one unassigned general purpose input/output pin: ? general purpose input/output 1 (gpio1, pin 1); input/output 3.2.1.5 no connects three pins are not used: ? no connect 1 (nc1, pin 8); no internal connection ? no connect 2 (nc2, pin 22); no internal connection ? no connect 3 (nc3, pin 25); no internal connection 3.2.2 cx20493 lsd pin assignments and signal definitions cx20493 lsd hardware interface signals are show n by major interface in figure 3-5, are shown by pin number in figure 3-6, and are listed by pin number in table 3-7. cx20493 lsd hardware interface sign als are defined in table 3-8. cx20493 lsd gpio dc electrical charact eristics are specified in table 3-9. cx20493 lsd avdd dc elec trical characteristics are listed in table 3-10. figure 3-5. cx20493 lsd hardware interface signals rac2 tac2 rac1 tac1 eic trdc eio eif rxi vz txo txf rbias vref vc gpio1 nc1 nc2 nc3 19 18 21 20 11 12 17 16 9 10 14 13 5 4 3 1 8 22 25 101701_006 cx20493 smartdaa 3 line side device (lsd) 28-pin qfn electronic inductor, off-hook, pulse dial, and tip and ring vi control agnd_lsd safety and emi protection ring filter agnd_lsd c944 receive coupling impedance matching and transmitter nc nc nc nc r954 agnd_lsd dvdd clk pwr+ avdd agnd dib_p dib_n paddle dc_gnd dgnd 24 26 7 2 6 27 28 29 15 23 c930 c928 agnd_lsd digital isolation barrier (dib) pwrclkn pwrclkp dib_datap dib_datan data channel power and clock channel r922 c922 c924 telephone line connector tip ring c926 r932 vdd c952 c950 note: consult applicable reference design for exact component placement and values, and for layout guidelines. c962 c974 c976 r990 c970 c978 dgnd_lsd vdd agnd_lsd dgnd_lsd gnd_tie u908 c940 fb906 on-hook monitor (optional) r950 r952 agnd_lsd br908 br908 cc br908 ac1 pclk2 clk2 +- r924 r926
cx81801-7x/8x smartv.xx modem data sheet 3-24 conexant 102199b figure 3-6. cx20493 lsd 28-pin qfn pin signals 101701a_007 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 1 9 1 8 1 7 1 6 1 5 g p i o 1 a v d d v c v r e f r b i a s a g n d p w r + r a c 1 t a c 1 r a c 2 t a c 2 e i o e i f d c _ g n d n c 1 r x i v z e i c t r d c t x f t x o d i b _ n d i b _ p c l k n c 3 d v d d d g n d n c 2 cx20493 table 3-7. cx20493 lsd 28-pin qfn pin signals pin signal label pin signal label 1 gpio1 15 dc_gnd 2 avdd 16 eif 3 vc 17 eio 4 vref 18 tac2 5 rbias 19 rac2 6 agnd 20 tac1 7 pwr+ 21 rac1 8 nc1 22 nc2 9 rxi 23 dgnd 10 vz 24 dvdd 11 eic 25 nc3 12 trdc 26 clk 13 txf 27 dib_p 14 txo 28 dib_n
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-25 table 3-8. cx20493 lsd hardware signal definitions label pin i/o i/o type signal name/description system signals avdd 2 pwr pwr regulated power output. provides external power for lsd digital circuits and a connection point for ex ternal decoupling. (avdd is routed internally to lsd analog circuits.) see pwr+ pin description. connect to lsd dvdd pin and connect to agnd_lsd through c928 and c930 in parallel. c928 and c930 must be placed close to pins 2 and 6. c930 must have esr < 2 ? . agnd 6 agnd_lsd agnd_lsd analog ground. connect to minus (-) terminal of full wave rectifier (fwr). connect fwr br980 terminal to dib transformer secondary winding undotted terminal through r922. vref 4 ref ref output reference voltage. connect to agnd_lsd through c940 and c976, which must be placed close to pi n 4. ensure a very close proximity between c940 and the vref pin. c940 must have a maximum esr of 2 ? . vref 4 ref ref output reference voltage. connect to agnd_lsd through c940 and c976, which must be placed close to pi n 4. ensure a very close proximity between c940 and the vref pin. c940 must have a maximum esr of 2 ? . vc 3 ref ref output middle reference voltage. connect to agnd_lsd through c944 and c974, which must be placed close to pin 3. ensure a very close proximity between c944 and the vc pin. use a short path and a wide trace to agnd_lsd pin. pwr+ 7 pwr pwr unregulated power input. provides unregulated input power to the lsd. pwr+ pin is an input which takes unregulated +3.2v to +4.5v from the dib power supply made up of the transformer, full-wave rectifier, and filter capacitors. the pwr+ input is regulated by an internal linear regulator to +3.3v 5% which is routed to the avdd pin. if pwr+ is less than +3.4v, then avdd is equal to the unregulated pwr+ input value minus 150 mv (table 3-10). connect to plus (+) terminal of fwr. connect terminal br908 ac1 to dib transformer secondary winding dotted terminal through r990. connect transformer side of fb906 to agnd_lsd though c970. place fb906 and c970 close to pin 7 and pin 6 (agnd). dvdd 24 pwr pwr digital power input. input power for lsd digita l circuits. connect to lsd avdd pin and connect to dgnd_lsd th rough c978. place c978 near pin 24. dgnd 23 dgnd_lsd dgnd_lsd lsd digital ground. connect to dgnd_lsd, and to agnd_lsd at the dgnd_lsd/agnd_lsd tie point (u908). paddle ? agnd_lsd agnd_lsd paddle ground. referred to as pin 29 in schematics. connect to agnd_lsd. dib interface signals clk 26 i i clock. provides input clock, ac coupled to the lsd . connect to dib transformer secondary winding undotted terminal through c926 (closest to the cx20493), r932, then r922 in series. connect the r932 and r922 node to lsd agnd pin through full-wave rectifier br908. place c926 near pin 26 and place r932 near c926. dib_p 27 i/o i/o data and control positive. connect to dibdat_p through r924 in series with c922. dib_p and dib_n signals are differential and half- duplex bidirectional. dib_n 28 i/o i/o data and control negative. connect to dibdat_n through r926 in series with c924. dib_p and dib_n signals are differential and half- duplex bidirectional.
cx81801-7x/8x smartv.xx modem data sheet 3-26 conexant 102199b table 3-8. cx20493 lsd hardware signal definitions (continued) label pin i/o i/o type signal name/description tip and ring interface rac1 tac1 21 20 i i ia ia ring1 ac coupled and tip1 ac coupled. ac-coupled voltage from telephone line used to detect ring. connect rac1 to the diode bridge ac node (ring) through r902 (connects to pin 21) and c902 in series. connect tac1 to the diode bridge ac node (tip) through r904 (connects to pin 20) and c904 in series. rac2 tac2 19 18 i i ia ia ring2 ac coupled and tip2 ac coupled. ac-coupled voltage from telephone line used to optionally detect signal while on-hook. connect rac2 to the diode bridge ac node (ring) through r948 (connects to pin 19) and c948. leave open if not used. connect tac2 to the diode bridge ac node (tip) through r946 (connects to pin 21) and c946. leave open if not used. eic 11 o oa electronic inductor capacitor switch. internally switched to trdc when pulse dialing. connect to agnd_lsd through c958. trdc 12 i ia tip and ring dc measurement. input on-hook voltage (from a resistive divider). used internally to extract tip and ring dc voltage and line polarity reversal (lpr) information. r906 and c918 must be placed very close to pin 12. eio 17 o oa electronic inductor output. calculated voltage is applied to this output to control off-hook and dc vi mask operation. connect to base of q902. dc_gnd 15 gnd agnd_lsd lsd electronic inductor ground. connect to agnd_lsd and to the gnd_lsd/agnd_lsd tie point (u908). eif 16 i ia electronic inductor feedback. connect to emitter of q904 through r968. rxi 9 i ia receive analog input. receiver operational amplifier inverting input. ac coupled to the bridge cc node through r910 (connects to pin 9) and c912 in series. r910 and c912 must be placed very close to pin 9. the length of the pcb trace connecting r910 to the rxi pin must be kept at an absolute minimum. rbias 5 i ia receiver bias. connect to agnd_lsd through r954, which must be placed close to pin 5. vz 10 i ia virtual impedance. input signal used to provide line complex impedance matching for worldwide c ountries. ac coupled to bridge cc node through r908 (connects to pin 10) and c910 in series. r908 and c910 must be placed very close to pin 10. the length of the pcb trace connecting r908 to the vz pin must be kept at an absolute minimum. txo 14 o oa transmit output. outputs transmit signal and impedance matching signal; connect to base of tr ansmitter transistor q906. txf 13 i ia transmit feedback. connect to emitter of transmitter transistor q906. not used gpio1 1 i/o it/ot12 general purpose i/o 1 . leave open if not used. nc1 8 no connect. no internal connection. leave open. nc2 22 no connect. no internal connection. leave open. nc3 25 no connect. no internal connection. leave open. notes: 1. i/o types*: ia analog input it digital input, ttl-compatible oa analog output ot12 digital output, ttl-compatible, 12 ma, z internal = 32 ? agnd_lsd isolated lsd analog ground gnd_lsd isolated lsd digital ground *see cx20493 lsd gpio dc electrical characteristics ( error! reference source not found. ). 2. refer to applicable reference design for exact component placement and values.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-27 table 3-9. cx20493 lsd gpio dc electrical characteristics parameter symbol min. typ. max. units test conditions input voltage v in -0.30 ? 3.465 v dvdd = +3.465v input voltage low v il ? ? 1.0 v input voltage high v ih 1.6 ? ? v output voltage low v ol 0 ? 0.33 v output voltage high v oh 2.97 ? ? v input leakage current ? -10 ? 10 a output leakage current (high impedance) ? -10 ? 10 a gpio output sink current at 0.33 v maximum ? 2.4 ? - ma gpio output source current at 2.97 v minimum ? 2.4 ? - ma gpio rise time/fall time 20 100 ns test conditions unless otherwise stated: dvdd = +3.3v +5%; ta = 0c to 70c; external load = 50 pf table 3-10. cx20493 avdd dc electrical characteristics pwr+ input avdd output +3.4v < pwr+ < +4.5v +3.3v 5% +3.2v < pwr+ < +3.39v 3.05v < avdd < 3.24v see pwr+, avdd, and dvdd descriptions in table 3-8.
cx81801-7x/8x smartv.xx modem data sheet 3-28 conexant 102199b 3.3 cx20442 vc hardware pins and signals (s models) 3.3.1 cx20442 vc signal summary microphone and analog speaker interface sign als, as well as telephone handset/headset interface signals are pr ovided to support functions such as speakerphone mode, telephone emulation, microphone voice record, speaker voice playback, and call progress monitor. 3.3.1.1 speakerphone interface the following signals are supported: ? speaker out (m_spkr_out); analog output - should be used in speakerphone designs where sound quality is important ? microphone (m_mic_in); analog input 3.3.1.2 telephone handset/headset interface the following interface signals are supported: ? telephone input (m_line_in), input (telin) - optional connection to a telephone handset interface circuit ? telephone output (m_line_outp); output (telout) - optional connection to a telephone handset interface circuit ? center voltage (vc); output reference voltage 3.3.1.3 cx81801 modem interface the following interface signals are supported: ? sleep (sleep); input ? master clock (m_clkin); input ? serial clock (m_sck); output ? control (m_cntrlsin); input ? serial frame sync (m_strobe); output ? serial transmit data (m_txsin); input ? serial receive data (m_rxout); output 3.3.1.4 host interface the following interface signals are supported: ? reset (por); input
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-29 3.3.2 cx20442 vc pin assignments and signal definitions vc 32-pin tqfp hardware interface signals are shown by major interface in figure 3-7, are shown by pin number in figure 3-8, and are listed by pin number in table 3-11. vc hardware interface signal s are defined in table 3-12. vc pin signal dc electrical character istics are defined in table 3-13. vc pin signal analog electrical charact eristics are defined in table 3-14.
cx81801-7x/8x smartv.xx modem data sheet 3-30 conexant 102199b figure 3-7. cx20442 vc hardware interface signals 102199_009 cx20442 voice codec (vc) 32-pin tqfp audio circuit nc spkout mic telin telout cx81801 +3.3v vaa (+3.3v) 1 4 19 21 23 20 22 18 17 25 5 28 26 6 27 iasleep dreset# m_clk v_sclk v_strobe v_txsin v_rxout v_ctrl sleep por m_clkin m_sck m_strobe m_txsin m_rxout m_cntrlsin vdd vdd mavdd vss set3v_bar2 mavss vsub m_dig_speaker m_mic_in m_spkr_out m_line_in m_line_outp m_line_outm vref vc m_mic_bias m_relaya m_relayb m_act90 m_1bit_out d_lpbk_bar nc nc nc 2 13 3 14 9 10 11 12 15 24 16 29 30 31 7 8 32 agnd 0.1uf 10uf handset interface nc agnd gnd agnd 0.1uf 10uf figure 3-8. cx20442 vc 32-pin tqfp pin signals 102199_010 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 3 2 3 1 3 0 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 1 9 1 8 1 7 s l e e p m _ d i g _ s p e a k e r m _ s p k r _ o u t p o r m a v d d m a v s s n c n c m _ r e l a y a m _ s t r o b e m _ r x o u t m _ s c k m _ t x s i n m _ c l k i n m _ c n t r l s i n v d d m _ l i n e _ o u t p m _ l i n e _ o u t m v r e f v c m _ m i c _ i n m _ l i n e _ i n m _ m i c _ b i a s m _ r e l a y b n c d _ l p b k _ b a r m _ 1 b i t _ o u t m _ a c t 9 0 v s s v s u b s e t 3 v _ b a r 2 v d d cx20442
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-31 table 3-11. cx20442 vc 32-pin tqfp pin signals pin signal label i/o interface 1 sleep i cx81801: iasleep 2 m_dig_speaker o nc 3 m_spkr_out o speaker interface circuit 4 por i host: reset# or reset circuit 5 mavdd p vaa (+3.3v) 6 mavss g agnd 7 nc nc 8 nc nc 9 m_line_outp o handset in terface circuit: telout 10 m_line_outm o nc 11 vref agnd through capacitors 12 vc agnd through capacitors 13 m_mic_in i microphone interface circuit 14 m_line_in i handset in terface circuit: telin 15 m_mic_bias nc 16 m_relayb nc 17 vdd p +3.3v 18 m_cntrlsin i cx81801: v_ctrl 19 m_clkin i cx81801: m_clk 20 m_txsin i cx81801: v_txsin 21 m_sck o cx81801: v_sclk 22 m_rxout o cx81801: v_rxout 23 m_strobe o cx81801: v_strobe 24 m_relaya o nc 25 vdd p +3.3v 26 m_set3v_bar2 i gnd 27 vsub g agnd 28 vss g gnd 29 m_act90 i nc 30 m_1bit_out o nc 31 d_lpbk_bar i nc 32 nc nc
cx81801-7x/8x smartv.xx modem data sheet 3-32 conexant 102199b table 3-12. cx20442 vc pin signal definitions label pin i/o i/o type signal name/description system signals vdd 17, 25 p pwr digital power supply. connect to +3.3v and digital circuits power supply filter. mavdd 5 p pwr analog power supply. connect to +3.3v and analog circuits power supply filter. vss 28 g gnd digital ground. connect to gnd. mavss 6 g agnd analog ground. connect to agnd. vsub 27 g gnd analog ground. connect to agnd. por 4 i itpu power-on reset. active low reset input. connect to host reset# or reset circuit. set3v_bar2 26 i itpu set +3.3v analog reference. connect to gnd. cx81801 interconnect sleep 1 i itpd ia sleep. active high sleep input. connect to cx81801 iasleep pin. m_clkin 19 i itpd master clock input . connect to cx81801 m_clk pin. m_sck 21 o ot2 serial clock output. connect to cx81801 v_sclk pin. m_cntrl_sin 18 i itpd control input. connect to cx81801 v_ctrl pin. m_strobe 23 o ot2 serial frame sync. connect to cx81801 v_strobe pin. m_txsin 20 i itpd serial transmit data. connect to cx81801 v_txsin pin. m_rxout 22 o ot2 serial receive data. connect to cx81801 v_rxout pin. microphone/speaker interface m_mic_in 13 i i(da) microphone input. single-ended analog input from the microphone circuit. m_spkr_out 3 o o(df) modem speaker analog output. the m_spkr_out analog output reflects the rece ived analog input signal. the m_spkr_out on/off and three levels of attenuation are controlled by bits in dsp ram. when the speaker is turned off, the m_spkr_out output is clamped to the voltage at the vc pin. the m_spkr_out output can drive an impedance as low as 300 ? . in a typical application, the m_spkr_out output is an input to an external lm386 audio power amplifier. handset/headset interface m_line_outp 9 o o(df) telephone handset out (telout). single-ended analog data output to the telephone handset circuit. the output can drive a 300 ? load. m_line_in 14 i i(da) telephone handset out (telin). single-ended analog data input from the telephone handset circuit.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-33 table 3-15. cx20442 vc pin signal definitions (continued) label pin i/o i/o type signal name/description reference voltage vref 11 r ref high voltage reference. connect to analog ground through 10 f (polarized, + terminal to vref) and 0.1 f (ceramic) in parallel. ensure a very close proximity between these capacitors and vref pin. vc 12 r ref low voltage reference. connect to analog ground through 10 f (polarized, + terminal to vc) and 0.1 f (ceramic) in parallel. ensure a very close proximity between these capacitors and vc pin. for handset interface, also c onnect to handset interface circuit (vc_hand). not used m_dig_speaker 2 o ot2 not used. leave open. m_line_outm 10 o oa not used. leave open. m_relaya 24 o ot not used. leave open. m_relayb 16 o ot not used. leave open. m_mic_bias 15 o oa not used. leave open. m_act90 29 i itpu not used. leave open. m_1bit_out 30 o ot2 not used. leave open. d_lpbk_bar 31 i it not used. leave open. nc 7, 8, 32 internal no connect. leave open. notes: 1. i/o types*: ia analog input it digital input, ttl-compatible itpd digital input, ttl-compatible, internal 75k 25k ? pull-down itpu digital input, ttl-compatible, internal 75k 25k ? pull-up oa analog output ot2 digital output, ttl-compatible, 2 ma, z internal = 120 ? ot2od digital output, ttl-compatible, 2 ma, open drain, z internal = 120 ? agnd analog ground gnd digital ground table 3-13. cx20442 vc dc electrical characteristics parameter symbol min. typ. max. units test conditions input voltage v in -0.30 ? vdd+0.3 v input voltage low v il -0.30 ? 0.2 *vdd v input voltage high v ih 0.4*vdd ? vdd+0.3 v output voltage low v ol 0 ? 0.4 v output voltage high v oh 0.8*vdd ? vdd v input leakage current ? -10 ? 10 a output leakage current (high impedance) ? -10 ? 10 a test conditions unless otherwise stated: vdd = +3.3 0.3 vdc; ta = 0c to 70c; external load = 50 pf
cx81801-7x/8x smartv.xx modem data sheet 3-34 conexant 102199b table 3-14. cx20442 vc analog electrical characteristics signal name type characteristic value m_line_in, i (da) input impedance > 70k ? m_mic_in ac input voltage range 1.1 vp-p reference voltage +1.35 vdc m_line_outp o (dd) minimum load 300 ? maximum capacitive load 0 f output impedance 10 ? ac output voltage range 1.4 vp-p (with reference to ground and a 600 ? load) reference voltage +1.35 vdc dc offset voltage 200 mv m_spkr_out o (df) minimum load 300 ? maximum capacitive load 0.01 f output impedance 10 ? ac output voltage range 1.4 vp-p reference voltage +1.35 vdc dc offset voltage 20 mv test conditions unless otherwise stated: vdd = +3.3 0.3 vdc; mavdd = +3.3 0.3 vdc, ta = 0c to 70c parameter min typ max units dac to line driver output (600 ? load, 3db in scf and ctf) snr/sdr at: 4vp-p differential 2vp-p differential -10dbm differential 88/85 82/95 72/100 db dac to speaker driver output (150 ? load, 3db in scf and ctf, -6db in speaker driver) snr/sdr at: 2vp-p 1vp-p -10dbm 88/75 82/80 72/83 db line input to adc (6db in aaf) snr/sdr at ?10 dbm 80/95 db input leakage current (analog inputs) -10 10 a output leakage current (analog outputs) -10 10 a
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-35 3.4 electrical and environmental specifications 3.4.1 operating conditions, absolute maximum ratings, and power requirements the operating conditions are specified in table 3-15. the absolute maximum ratings are listed in table 3-16 for the cx81801, table 3-17 for the cx20493, and table 3-18 for the cx20442. the current and power requirements are listed in error! reference source not found. . table 3-15. operating conditions parameter symbol limits units supply voltage vdd +3.0 to +3.6 vdc operating ambient temperature t a 0 to +70 c table 3-16. cx81801 absolute maximum ratings parameter symbol limits units supply voltage vdd -0.5 to +4.0 vdc input voltage v in -0.5 to + (vgg + 0.5)* vdc storage temperature range t stg -55 to +125 c analog inputs v in -0.3 to (vaa + 0.5) vdc voltage applied to outputs in high impedance (off) state v hz -0.5 to + (vgg + 0.5)* vdc dc input clamp current i ik 20 ma dc output clamp current i ok 20 ma static discharge voltage (25c) v esd 2500 vdc latch-up current (25c) i trig 400 ma * vgg = +3.3v 0.3v, or +5v 0.25v table 3-17. cx20493 absolute maximum ratings parameter symbol limits units regulator supply voltage pwr+ -0.5 to +4.1 vdc supply voltage dvdd, avdd -0.5 to +3.6 vdc pin voltage i/o -0.5 to dvdd + 0.5 vdc storage temperature range t stg -55 to +125 c voltage applied to outputs in high impedance (off) state v hz -0.5 to +5.5 vdc static discharge voltage (hbm) v esd 2500 v latch-up current (25c) i trig 250 ma
cx81801-7x/8x smartv.xx modem data sheet 3-36 conexant 102199b table 3-18. cx20442 absolute maximum ratings parameter symbol limits units analog supply voltage avdd -0.3 to +4.6 v digital supply voltage vdd -0.3 to +4.6 v storage temperature range t stg ?55 to +150 c digital inputs v in ?0.3 to (vdd + 0.3) v analog inputs v in ?0.3 to + (avdd + 0.3) v dc input clamp current i ik 10 ma dc output clamp current i ok 10 ma static discharge voltage (25 c) v esd 2500 v latch-up current (25 c) i trig 150 ma notes: 1. ratings specified for +3.3 v operation. 2. voltages referenced to ground (vss). table 3-19. current and power requirements mode typical current (ityp) (ma) maximum current (imax) (ma) typical power (ptyp) (mw) maximum power (pmax) (mw) notes cx81801 modem and cx20493 lsd normal mode: off-hook, normal data connection 62 71 205 256 f = 28.224 mhz normal mode: on-hook, idle, waiting for ring 60 69 198 248 f = 28.224 mhz sleep mode 18 21 59 76 f = 0 mhz cx20442 vc (optional) normal mode 1.5 2.0 5 7 notes: 1. operating voltage: vdd = +3.3v 0.3v. 2. test conditions: vdd = +3.3v for typica l values; vdd = +3.6v for maximum values. 3. input ripple 0.1 vpeak-peak. 4. f = internal frequency. 5. typical power (ptyp) computed from ityp: ptyp = ityp * 3.3v; maximum power (pmax) computed from imax: pmax = imax * 3.6v. handling cmos devices the device contains circuitry to protect the inputs against damage due to high static voltages. however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltage. an unterminated input can acquire unpredictable voltages through coupling with stray capacitance and internal cross talk. both power dissipation and device noise immunity degrades. therefore, all inputs should be connected to an appropriate supply voltage. input signals should never exceed the voltage range from -0.5 v to + (vgg + 0.5v). this prevents forward biasing the input protection diodes and possibly entering a latch up mode due to high current transients.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-37 3.4.2 interface and timing waveforms 3.4.2.1 external memory bus timing the external memory bus timing is listed in table 3-20 and illustrated in figure 3-9. table 3-20. timing - external memory bus symbol parameter min typ. max units t fi internal operating frequency 28.224 ? ? mhz t cyc internal operating clock cycle 30 ? ? ns read t as read# high to address valid ? 6.5 9 ns t es read# high to es valid ? 8 11 ns t rw read# pulse width 15 ? 105 ns t rds read data valid to read# high 6.1 ? ? ns t rdh read# high to read data hold 0 0 ? ns write t as write# high to address valid ? 6.5 8 ns t es write# high to es valid ? 8 11 ns t ww write# to write# pulse width 15 ? 105 ns t wtd write# low to write data valid ? 5 8.2 ns t wth write# high to write data hold 5.0 ? ? ns notes: 1. es = ramsel# or romsel#. 2. read pulse width and write pulse width: ram: t rw , t ww = 0.5 t cyc = 15 for non-extended cycle timing rom: t rw , t ww = 3.5 t cyc = 105 for extended cycle timing 3. memory speed determination: ram: t access = t cyc - t es - t rds = 330 - 8 - 6.1 = 15.9 ns (i.e., use 15 ns memory) rom: t access = 4(t cyc ) - t es - t rds = 4(30) - 8 - 6.1 = 105.9 ns (i.e., use 90 ns memory). 4. output enable to output delay timing: ram: t oe = t rw - t rds = 0.5(t cyc ) - t rds = 15 - 6.1 = 8.9 ns rom: t oe = t rw - t rds = 3.5(t cyc ) - t rds = 105 - 6.1 = 98.9 ns.
cx81801-7x/8x smartv.xx modem data sheet 3-38 conexant 102199b figure 3-9. waveforms - external memory bus write timing read timing t cyc t as rdh c2* a[18:0] t rw t t rds read# d[7:0] es#** t es * c2 = internal phase 2 clock. ** es# = ramsel# or romsel#. 100491 f3-09 wf eb t cyc t as t ww t t wth wtd es t c2* a[18:0] write# d[7:0] es#** * c2 = internal phase 2 clock. ** es# = ramsel# or romsel#.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-39 3.4.2.2 parallel host bus timing the parallel host bus timing is listed in table 3-21 and illustrated in figure 3-10. table 3-21. timing - parallel host bus symbol parameter min max units read (see notes 1, 2, 3, 4, and 5) t as address setup 5 ? ns t ah address hold 10 ? ns t cs chip select setup 0 ? ns t ch chip select hold 10 ? ns t rd hrd# strobe width 45 ? ns t dd read data delay ? 25 ns t drh read data hold 5 ? ns write (see notes 1, 2, 3, 4, and 5) t as address setup 5 ? ns t ah address hold 15 ? ns t cs chip select setup 0 ? ns t ch chip select hold 10 ? ns t wt hwt# strobe width 75 ? ns t ds write data setup (see note 4) ? 20 ns t dwh write data hold (see note 5) 5 ? ns notes: 1. when the host executes cons ecutive rx fifo reads, a minimum delay of 2 times the internal cpu clock cycle plus 15 ns (85.86 ns at 28.224 mhz) is required from the falling edge of hrd# to the falling edge of the next host rx fifo hrd# clock. 2. when the host executes consecutive tx fifo writes, a minimum delay of 2 times the internal cpu clock cycle plus 15 ns (85.86 ns at 28.224 mhz) is required from the falling edge of hwt# to the falling edge of the next host tx fifo hwt# clock. 3. t ds is measured from the point at wh ich both hcs# and hwt# are active. 4. t dwh is measured from the point at whic h either hcs# and hwt# become inactive. 5. clock frequency = 28.224 mhz clock.
cx81801-7x/8x smartv.xx modem data sheet 3-40 conexant 102199b figure 3-10. waveforms - parallel host bus t as t ah t cs t ch t rd t dd t drh ha[2-0] hcs# hrd# hwt# hd[7-0] t as t ah t cs t ch ha[2-0] t wt t ds t dwh hcs# hrd# hwt# hd[7-0] 100491 f3-10 wf-hb a. host read b. host write
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-41 3.4.2.3 serial dte interface the serial dte interface waveforms for 4800 an d 9600 bps are illustrated in figure 3-11. figure 3-11. waveforms - serial dte interface txclk 4800 bps txd 4800 bps txclk 9600 bps txd 9600 bps note: this figure is valid for synchronous mode only. there is no relationship between note: txd and txclk in asynchronous mode. rxclk 4800 bps rxd 4800 bps rxclk 9600 bps rxd 9600 bps note: this figure is valid for synchronous mode only. there is no relationship between note: rxd and rxclk in asynchronous mode. a. transmit b. receive 1227f3-14 wf-ser dte
cx81801-7x/8x smartv.xx modem data sheet 3-42 conexant 102199b 3.5 crystal specifications crystal specifications are listed in table 3-22. table 3-22. crystal specifications characteristic value frequency 28.224 mhz nominal calibration tolerance 50 ppm at 25c (c l = 16.5 and 19.5 pf) frequency stability vs. temperature 35 ppm (0c to 70c) frequency stability vs. aging 20 ppm/5 years oscillation mode fundamental calibration mode parallel resonant load capacitance, c l 18 pf nom. shunt capacitance, c o 7 pf max. series resistance, r 1 35-60 ? max. @20 nw drive level drive level 100w correlation; 500w max. operating temperature 0c to 70c storage temperature ?40c to 85c
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 3-43 this page is intentionally blank.

cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 4-1 4. package dimensions the 128-pin tqfp package dimensions are shown in figure 4-1. the 32-pin tqfp package dimensions are shown in figure 4-2. the 28-pin qfn package dimensions are shown in figure 4-3.
cx81801-7x/8x smartv.xx modem data sheet 4-2 conexant 102199b figure 4-1. package dimensions - 128-pin tqfp e b d d1 e1 detail a detail a a1 l1 c l a e1 e2 e d2 d1 a2 millimeters 0.05 21.75 15.75 0.5 0.17 0.11 1.6 max 0.15 1.4 ref 22.25 20.0 ref 18.5 ref 16.25 14.0 ref 12.5 ref 0.75 1.0 ref 0.50 bsc 0.27 0.17 0.08 max 0.0020 0.8563 0.6201 0.0197 0.0067 0.0043 a a1 a2 d d1 d2 e e1 e2 l l1 e b c coplanarity min. max. min. max. inches* dim. ref: 128-pin tqfp (gp00-d264) * metric values (millimeters) should be used for pcb layout. english values (inches) are converted from metric values and may include round-off errors. 0.0630 max 0.0059 0.0551 ref 0.8760 0.7874 ref 0.7283 ref 0.6398 0.5512 ref 0.4921 ref 0.0295 0.0394 ref 0.0197 bsc 0.0106 0.0067 0.0031 max pd-tqfp-128 (040395) pin 1 ref
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 4-3 figure 4-2. package dimensions - 32-pin tqfp detail a a1 l1 c l a d1 a2 millimeters 0.05 8.75 0.5 0.30 0.13 1.6 max 0.15 1.4 ref 9.25 7.0 ref 5.6 ref 0.75 1.0 ref 0.80 bsc 0.40 0.19 0.10 max 0.0020 0.3445 0.0197 0.0118 0.0051 a a1 a2 d d1 d2 l l1 e b c coplanarity min. max. min. max. inches* dim. ref: 32-pin tqfp (gp00-d262) * metric values (millimeters) should be used for pcb layout. english values (inches) are converted from metric values and may include round-off errors. 0.0630 max 0.0059 0.0551 ref 0.3642 0.2756 ref 0.2205 ref 0.0295 0.0394 ref 0.0315 bsc 0.0157 0.0075 0.004 max pd-tqfp-32 (040395) detail a d1 e b d d2 d1 d1 d d2 pin 1 ref
cx81801-7x/8x smartv.xx modem data sheet 4-4 conexant 102199b figure 4-3. package dimensions - 28-pin qfn max. 0.75 1.00 0.80 d e e1 d1 a a1 a3 a2 - - 0.00 5.00 5.00 4.75 4.75 0.20 0.65 0.01 0.85 0.05 l b 0.23 0.50 e min. 0.28 0.60 0.35 0.5 bsc nom. d2 e2 2.95 3.10 3.25 2.95 3.10 3.25 pd_gp00-d682-001 ref. gp00-d682-001 0.15 4.90 4.65 4.90 4.65 0.25 5.10 4.85 5.10 4.85 terminal tip top view e l c c c d1 3 pin 1 identifier 1 2 28 e e1 d bottom view 10 a1 plane seating b a2 a3 a1 a l e note 3 3 e2 2 d2 1 28 note 1 note 1 scale: none section "c-c" b pin 1 identifier notes: 1. dimension b applies to plated terminal and is measured between 0.20 and 0.25mm from terminal tip. 2. package warpage max 0.05mm. 3. applied for exposed pad and terminals. exclude embedding part of exposed pad from measuring. symbol dimensions (millimeters)
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 5-1 5. parallel host interface the modem supports a 16550a interface in parallel inte rface versions. the 16550a interface can operate in fifo mode or non-f ifo mode. non-fifo mode is the same as 16450 interface operation. fifo mode unique operations are identified. 5.1 overview the parallel interface registers and the co rresponding bit assignments are shown in table 5-1. the modem emulates the 16450 /16550a interface and include s both a 16-byte receiver data first-in first-out buffer (rx fifo) and a 16-byte transmit data first-in first-out buffer (tx fifo). when fifo mode is selected in the fifo control register (fcr0 = 1), both fifos are operative. furthermore, when fifo mode is selected, dma operation of the fifo can also be selected (fcr3 = 1). when fifo mode is not selected, operation is restricted to 16450 interface operation. the received data is read by the host fr om the receiver buffer (rx buffer). the rx buffer corresponds to the receiver buffer re gister in a 16550a device. in fifo mode, the rx fifo operates transparently behi nd the rx buffer. interface operation is described with reference to the rx buffer in both fifo and non-fifo modes. the transmit data is loaded by the host into the transmit buffer (tx buffer). the tx buffer corresponds to the transmit holding register in a 16550a device. in fifo mode, the tx fifo operates transparently behi nd the tx buffer. interface operation is described with reference to the tx buffer in both fifo and non-fifo modes.
cx81801-7x/8x smartv.xx modem data sheet 5-2 conexant 102199b table 5-1. parallel interface registers register register bit no. no. name 7 6 5 4 3 2 1 0 7 scratch register (scr) scratch register 6 modem status register (msr) data carrier detect (dcd) ring indicator (ri) data set ready (dsr) clear to send (cts) delta data carrier detect (ddcd) trailing edge of ring indicator (teri) delta data set ready (ddsr) delta clear to send (dcts) 5 line status register (lsr) rx fifo error transmitter empty (temt) transmitter buffer register empty (thre) break interrupt (bi) framing error (fe) parity error (pe) overrun error (oe) receiver data ready (dr) 4 modem control register (mcr) 0 0 0 local loopback out 2 out 1 request to send (rts) data terminal ready (dtr) 3 line control register (lcr) divisor latch access bit (dlab) set break stick parity even parity select (eps) parity enable (pen) number of stop bits (stb) word length select bit 1 (wls1) word length select bit 0 (wls0) 2 interrupt identify register (iir) (read only) fifos enabled fifos enabled 0 0 pending interrupt id bit 2 pending interrupt id bit 1 pending interrupt id bit 0 ?0" if interrupt pending 2 fifo control register (fcr) (write only) receiver trigger msb receiver trigger lsb reserved reserved dma mode select tx fifo reset rx fifo reset fifo enable 1 (dlab = 0) interrupt enable register (ier) 0 0 0 0 enable modem status interrupt (edssi) enable receiver line status interrupt (elsi) enable transmitter holding register empty interrupt (etbei) enable received data available interrupt (erbfi) 0 (dlab = 0) transmitter buffer register (thr) transmitter fifo buffer register (write only) 0 (dlab = 0) receiver buffer register (rbr) receiv er fifo buffer register (read only) 1 (dlab = 1) divisor latch msb register (dlm) divisor latch msb 0 (dlab = 1) divisor latch lsb register (dll) divisor latch lsb
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 5-3 5.2 register signal definitions 5.2.1 ier - interrupt enable regist er (addr = 1, dlab = 0) the ier enables five types of interrupts that can separately assert the hint output signal (table 5-2). a selected interrupt can be enabled by setting the corresponding enable bit to a 1, or disabled by setting the corresponding enable bit to a 0. disabling an interrupt in the ier prohibits setting the corresponding indication in the iir and assertion of hint. disabling all interrupts (resetting ier0 - ier3 to a 0) inhibits setting of any interrupt identifier register (iir) bits and inhibits as sertion of the hint output. all other system functions operate normally, including the setting of the line status register (lsr) and the modem status register (msr). bits 7-4 not used. always 0. bit 3 enable modem status interrupt (edssi). this bit, when a 1, enables assertion of the hint output whenever the delta cts (msr0), delta dsr (msr1), delta ter (msr2), or delta dcd (msr3) bit in the modem status register (msr) is a 1. this bit, when a 0, disables assertion of hint due to setting of any of these four msr bits. bit 2 enable receiver line status interrupt (elsi). this bit, when a 1, enables assertion of the hint output whenever the overrun error (lsr1), parity error (lsr2), framing error (lsr3), or break interrupt (lsr4) receiver status bit in the line status register (lsr) changes state. this bit, when a 0, disables assertion of hint due to ch ange of the receiver lsr bits 1-4. bit 1 enable transmitter holding register empty in terrupt (etbei). this bit, when a 1, enables assertion of the hint output when the transmitter empty bit in the line status register (lsr5) is a 1. this bit, when a 0, disables assertion of hint due to lsr5. bit 0 enable receiver data availabl e interrupt (erbfi ) and character timeout in fifo mode. this bit, when a 1, enables assertion of th e hint output when the receiver data ready bit in the line status register (lsr0) is a1 or character timeout occurs in the fifo mode. this bit, when a 0, disables assertion of hint due to the lsr0 or character timeout.
cx81801-7x/8x smartv.xx modem data sheet 5-4 conexant 102199b 5.2.2 fcr - fifo control register (addr = 2, write only) the fcr is a write-only register used to en able fifo mode, clear the rx fifo and tx fifo, enable dma mode, and set the rx fifo trigger level. bits 7-6 rx fifo trigger level. fcr7 and fcr6 set the trigger level for the rx fifo (receiver data available) interrupt. fcr7 fcr6 rx fifo trigger level (bytes) 0 0 01 0 1 04 1 0 08 1 1 14 bits 5-4 not used. bit 3 dma mode select. when fifo mode is selected (fcr0 = 1) , fcr3 selects non-dma operation (fcr3 = 0) or dma operation (fcr3 = 1). when fifo mode is not selected (fcr0 = 0), this bit is not used (the modem operates in non-dma mode in 16450 operation). dma operation in fifo mode. rxrdy will be asserted when the number of characters in the rx fifo is equal to or greater than the value in the rx fifo tr igger level (iir0-iir3 = 4h) or the received character timeout (iir0-iir3 = ch) has o ccurred. rxrdy will go inactive when there are no more characters in the rx fifo. txrdy will be asserted when there are one or more empty (unfilled) locations in the tx fifo. txrdy will go inactive when the tx fifo is completely full. non-dma operation in fifo mode. rxrdy will be asserted when there are on e or more characters in the rx fifo. rxrdy will go inactive when there are no more characters in the rx fifo. txrdy will be asserted when there are no characters in the tx fifo. txrdy will go inactive when the first character is loaded into the tx fifo buffer. bit 2 tx fifo reset. when fcr2 is a 1, all bytes in the tx fifo are cleared. this bit is cleared automatically by the modem. bit 1 rx fifo reset. when fcr1 is a 1, all bytes in the rx fifo are cleared. this bit is cleared automatically by the modem. bit 0 fifo enable. when fcr0 is a 0, 16450 mode is selected and all bits are cleared in both fifos. when fcr0 is a 1, fifo mode (16550a mode) is selected and both fifos are enabled. fcr0 must be a 1 when other bits in the fcr are written or they will not be acted upon.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 5-5 5.2.3 iir - interrupt identifier register (addr = 2) the interrupt identifier register (iir) identif ies the existence and type of up to five prioritized pending interrupts. four priority leve ls are set to assist interrupt processing in the host. the four levels, in order of decr easing priority, are: highest: receiver line status, 2: receiver data available or recei ver character timeout, 3: tx buffer empty, and 4: modem status. when the iir is accessed, the modem freezes all interrupts and indicates the highest priority interrupt pending to the host. any change occurring in in terrupt conditions are not indicated until this access is complete. bits 7-6 fifo mode. these two bits copy fcr0. bits 5-4 not used. always 0. bits 3-1 highest priority pending interrupt. these three bits identify the highest priority pending interrupt (table 5-2). bit 3 is applicable only when fifo mode is selected, otherwise bit 3 is a 0. bit 0 interrupt pending. when this bit is a 0, an interrupt is pending; iir bits 1-3 can be used to determine the source of the interrupt. when this bit is a1, an interrupt is not pending. table 5-2. interrupt sources and reset control interrupt identification register interrupt set and reset functions bit 3 1 bit 2 bit 1 bit 0 priority level interrupt type interrupt source interrupt reset control 0 0 0 1 ? none none ? 0 1 1 0 highest receiver line status overrun error oe (lsr1), parity error (pe) (lsr2), framing error (fe) (lsr3), or break interrupt (bi) (lsr4) reading the lsr 0 1 0 0 2 received data available received data available (lsr0) or rx fifo trigger level (fcr6- fcr7) reached 1 reading the rx buffer or the rx fifo drops below the trigger level 1 1 0 0 2 character time-out indication 1 the rx fifo contains at least 1 character and no characters have been removed from or input to the rx fifo during the last 4 character times. reading the rx buffer 0 0 1 0 3 tx buffer empty tx buffer em pty reading the iir or writing to the tx buffer 0 0 0 0 4 modem status delta cts (dcts) (msr0), delta dsr (ddsr) (msr1), trailing edge ring indicator (teri) (msr3), or delta dcd (dcd) (msr4) reading the msr notes: 1. fifo mode only.
cx81801-7x/8x smartv.xx modem data sheet 5-6 conexant 102199b 5.2.4 lcr - line control register (addr = 3) the line control register (lcr) specifies the format of the asynchronous data communications exchange. bit 7 divisor latch access bit (dlab). this bit must be set to a 1 to access the divisor latch registers during a read or write operation. it must be reset to a 0 to acces s the receiver buffer, the transmitter buffer, or the interrupt enable register. bit 6 set break. when bit 6 is a 1, the transmit data is fo rced to the break cond ition, i.e., space (0) is sent. when bit 6 is a 0, break is not sent. the set break bit acts only on the transmit data and has no effect on the serial in logic. bit 5 stick parity. when parity is enabled (lcr3 = 1) and stick parity is selected (lcr5 = 1), the parity bit is transmitted and checked by the receiver as a 0 if even parity is selected (lcr4 = 1) or as a 1 if odd parity is selected (l cr4 = 0). when stick parity is not selected (lcr3 = 0), parity is transmit and checked as determined by the lcr3 and lcr4 bits. bit 4 even parity select (eps). when parity is enabled (lcr3 = 1) and stic k parity is not selected (lcr5 = 0), the number of 1s transmitted or checked by the r eceiver in the data word bits and parity bit is either even (lcr4 = 1) or odd (lcr4 = 0). bit 3 enable parity (pen). when bit 3 is a 1, a parity bit is generated in the serial out (transmit) data stream and checked in the serial in (receive) data str eam as determined by the lcr 4 and lcr5 bits. the parity bit is located between the last data bit and the first stop bit. bit 2 number of stop bits (stb). this bit specifies the number of stop bits in each serial out character. if bit 2 is a 0, one stop bit is generated regardless of word length. if bit 2 is a 1 and 5-bit word length is selected, one and one-half stop bits are generated. if bit 2 is a 1 and a 6-, 7-, or 8-bit word length is selected, two stop bits are ge nerated. the serial in logic checks the first stop bit only, regardless of the number of stop bits selected. bits 1-0 word length select (wls0 and wls1). these two bits specify the numbe r of bits in each serial in or serial out character. the encoding of bits 0 and 1 is: bit 1 bit 0 word length 0 0 5 bits (not supported) 0 1 6 bits (not supported) 1 0 7 bits 1 1 8 bits
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 5-7 5.2.5 mcr - modem control register (addr = 4) the modem control register (m cr) controls the interface with the modem or data set. bit 7-5 not used. always 0. bit 4 local loopback. when this bit is set to a 1, the diagnostic mode is selected and the following occurs: data written to the transmit buffer is looped back to the receiver buffer. the dts (mcr0), rts (mcr1), out1 (mcr2), and out2 (mcr3) modem control register bits are internally connected to the dsr (msr5), cts (m sr4), ri (msr6), and dcd (msr7) modem status register bits, respectively. bit 3 output 2. when this bit is a 1, hint is enabled. when this bit is a 0, hint is in the high impedance state. bit 2 output 1. this bit is used in local loopback (see mcr4). bit 1 request to send (rts). this bit controls the request to send (rts) function. when this bit is a 1, rts is on. when this bit is a 0, rts is off. bit 0 data terminal ready (dtr). this bit controls the data terminal ready (d tr) function. when this bit is a 1, dtr is on. when this bit is a 0, dtr is off. 5.2.6 lsr - line status register (addr = 5) this 8-bit register provides status informa tion to the host concerning data transfer. bit 7 rx fifo error. in the 16450 mode, this bit is not used and is always 0. in the fifo mode, this bit is set if there are one or more characters in the rx fifo with a parity error, framing error, or break indication detected. this bit is reset to a 0 when the host reads the lsr and none of the above conditions exist in the rx fifo. bit 6 transmitter empty (temt). this bit is set to a 1 whenever the tx buff er (thr) and equivalent of the transmitter shift register (tsr) are both empty. it is re set to a 0 whenever either the thr or the equivalent of the tsr contains a character. in the fifo mode, this bit is set to a 1 wh en ever the tx fifo and the equivalent of the tsr are both empty.
cx81801-7x/8x smartv.xx modem data sheet 5-8 conexant 102199b bit 5 transmitter holding register empty (thre) [tx buffer empty]. this bit, when set, indicates that the tx buffer is empty and the modem can accept a new character for transmission. in addition, this bit causes the modem to issue an interrupt to the host when the transmit holding register empty interrupt enable bit (iir1) is set to 1. the thre bit is set to a 1 when a character is transferred from the tx buffer. the bit is reset to 0 when a byte is written into the tx buffer by the host. in the fifo mode, this bit is set when the tx fifo is empty; it is cleared when at least one byte is in the tx fifo. bit 4 break interrupt (bi). this bit is set to a 1 whenever the receive d data input is a space (logic 0) for longer than two full word lengths plus 3 bits. the bi bit is reset when the host reads the lsr. bit 3 framing error (fe). this bit indicates that the rece ived character did not have a valid stop bit. the fe bit is set to a 1 whenever the stop bit following the last data bit or parity bit is detected as a logic o (space). the fe bit is reset to a 0 when the host reads the lsr. in the fifo mode, the error indication is asso ciated with the particular character in the fifo it applies to; the fe bit is set to a 1 when this character is loaded into the rx buffer. bit 2 parity error (pe). this bit indicates that the received data ch aracter in the rx buff er does not have the correct even or odd parity, as selected by the even parity select bit (lcr4) and the stick parity bit (lcr5). the pe bit is reset to a 0 when the host reads the lsr. in the fifo mode, the error indication is asso ciated with the particular character in the it applies to; the pe bit is set to a 1 when th is character is loaded into the rx buffer. bit 1 overrun error (oe). this bit is set to a 1 whenever received data is loaded into the rx buffer before the host has read the previous data from the rx buffer. the oe bit is reset to a 0 when the host reads the lsr. in the fifo mode, if data continues to fill beyond the trigger level, an overrun condition will occur only if the rx fifo is full and the next character has been completely received. bit 0 receiver data ready (dr). this bit is set to a 1 whenever a complete incoming character has been received and has been transferred into the rx buffer. the dr bit is reset to a 0 when the host reads the rx buffer. in the fifo mode, the dr bit is set when the number of received data bytes in the rx fifo equals or exceeds the trigger level specified in fcr0-fcr1.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 5-9 5.2.7 msr - modem status r egister (addr = 6) the modem status register (m sr) reports current state and change information of the modem. bits 4-7 supply current state and bits 0-3 supply change information. the change bits are set to a 1 whenever a control input from the modem changes state from the last msr read by the host. bits 0-3 are reset to 0 when the host reads the msr or upon reset. whenever bits 0, 1, 2, or 3 are set to a 1, a modem status interrupt (iir0-iir3 = 0) is generated. bit 7 data carrier detect (dcd). this bit indicates the logic state of the dc d# (rlsd#) output. if loopback is selected (mcr4 = 1), this bit reflects the state of the out2 bit in the mcr (mcr3). bit 6 ring indicator (ri). this bit indicates the logic state of the ri# output. if loopback is selected (mcr4 = 1), this bit reflects the state of the out1 bit in the mcr (mcr2). bit 5 data set ready (dsr). this bit indicates the logic state of the ds r# output. if loopback is selected (mcr4 = 1), this bit reflects the state of the dtr bit in the mcr (mcr0). bit 4 clear to send (cts). this bit indicates the logic state of the ct s# output. if loopback is selected (mcr4 = 1), this bit reflects the state of the rts bit in the mcr (mcr1). bit 3 delta data carrier detect (ddcd). this bit is set to a 1 when the dcd bit ch anges state since the msr was last read by the host. bit 2 trailing edge of ring indicator (teri). this bit is set to a 1 when the ri bit changes from a 1 to a 0 state since the msr was last read by the host. bit 1 delta data set ready (ddsr). this bit is set to a 1 when the dsr bit has changed since the msr was last read by the host. bit 0 delta clear to send (dcts). this bit is set to a 1 when the cts bit has changed since the msr was last read by the host. 5.2.8 rbr - rx buffer (receiver buffer register) (addr = 0, dlab = 0) the rx buffer (rbr) is a read-only register at location 0 (with dlab = 0). bit 0 is the least significant bit of the data, and is the first bit received. 5.2.9 thr - tx buffer (transmitter holding register) (addr = 0, dlab = 0) the tx buffer (thr) is a write-only register at address 0 when dlab = 0. bit 0 is the least significant bit and the first bit sent.
cx81801-7x/8x smartv.xx modem data sheet 5-10 conexant 102199b 5.2.10 divisor registers (addr = 0 and 1, dlab = 1) the divisor latch ls (least significant byte) and divisor latch ms (most significant byte) are two read-write registers at locati ons 0 and 1 when dlab = 1, respectively. the baud rate is selected by loading each divisor latch with the appropriate hex value. programmable values corresponding to the desired baud rate are listed in table 5-3. 1. scr - scratch register (addr = 7) the scratchpad register is a read-write register at location 7. this register is not used by the modem and can be used by the host for temporary storage. table 5-3. programmable baud rates divisor latch (hex) ms ls divisor (decimal) baud rate 06 00 1536 75 04 17 1047 110 03 00 768 150 01 80 384 300 00 c0 192 600 00 60 96 1200 00 30 48 2400 00 18 24 4800 00 0c 12 9600 00 06 6 19200 00 04 4 28800 00 03 3 38400 00 02 2 57600 00 01 1 115200 00 00 na 230400 5.3 receiver fifo interrupt operation 5.3.1 receiver data available interrupt when the fifo mode is enabled (fcr0 = 1) and receiver interrupt (rx data available) is enabled (ier0 = 1), receiver in terrupt operation is as follows: the receiver data available flag (lsr0) is se t as soon as a received data character is available in the rx fifo. lsr0 is cl eared when the rx fifo is empty. the receiver data available interrupt code (i ir0-iir4 = 4h) is set whenever the number of received data bytes in the rx fifo reach es the trigger level specified by fcr6-fcr7 bits; it is cleared whenever the number of received data bytes in the rx fifo drops below the trigger level specified by fcr6-fcr7 bits. the hint interrupt is asserted whenever the number of received data bytes in the rx fifo reaches the trigger level specified by fcr6-fcr7 bits. hint interrupt is de- asserted when the number of received data byt es in the rx fifo dr ops below the trigger level specified by fcr6-fcr7 bits.
cx81801-7x/8x smartv.xx modem data sheet 102199b conexant 5-11 5.3.2 receiver character timeout interrupts when the fifo mode is enabled (fcr0 = 1) and receiver interrupt (receiver data available) is enabled (ier0 = 1), receiver character timeout interrupt operation is as follows: 1. a receiver character timeout interrupt code (iir0-iir3 = ch) is set if at least one received character is in the rx fifo, the most recent received serial character was longer than four continuous character tim es ago (if 2 stop bits are specified, the second stop bit is included in this time period), and the most recent host read of the rx fifo was longer than four continuous character times ago. 5.4 transmitter fifo interrupt operation 5.4.1 transmitter empty interrupt when the fifo mode is enabled (fcr0 = 1) and transmitter interrupt (tx buffer empty) is enabled (ier0 = 1), transmitter interrupt operation is as follows: the tx buffer empty interrupt code (iir0-ii r3 = 2h) will occur when the tx buffer is empty; it is cleared when the tx buffer is wr itten to (1 to 16 char acters) or the iir is read. the tx buffer empty indications will be delayed 1 character time minus the last stop bit time whenever the following o ccur: thre = 1 and there have not been at least two bytes at the same time in the tx fifo buffer sinc e the last setting of thre was set. the first transmitter interrupt after setting fcr0 will be immediate.
cx81801-7x/8x smartv.xx modem data sheet 5-12 conexant 102199b this page is intentionally blank.
notes
www.conexant.com general information: u.s. and canada: (888) 855-4562 international: (732) 345-7500 headquarters ? red bank 100 schulz drive red bank, nj 07701

▲Up To Search▲

Price & Availability of DS96-L147-203

	To Download DS96-L147-203 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .